Start
XR2
Xnity Remote
TV Power
XFINITY / Menu
Access Guide, Saved,
XFINITY On Demand, Apps,
Search and Settings.
Search
Discover content by
channel, program or
key words.
TV Input
Changes to the next
available input on your T V
(if programmed in Step 4)
All Power
Setup
Program remote for Aim
Anywhere or to control your
TV or audio device.
Swap
Switches between two DVR
tuners so you can control
playback of two channels.
Number Keys
1 Meet Your Remote 2 Turn On Your Remote
Install batteries in the remote and turn on your devices.
Turn on your TV.B
To set up your remote, rst install AA batteries
(sold separately). The All Power key will blink
green four times as the remote powers up
(about 5 seconds).
A
Turn on your cable box.C
Back
3
Your remote is preprogrammed to operate XFINITY cable boxes. If you are
using the remote for control of a non-XFINITY cable box, you may need to
program the remote for the Motorola or Cisco mode. Follow the steps below to
program your remote.
Press the Setup button until the All Power key
on the remote changes from red to green.
Press B for control of a Motorola brand
cable box; press C for control of a Cisco
or Scientic-Atlanta brand cable box.
Note: If you need to re-program the remote
for control of an XFINITY cable box, repeat
the steps above and press A in step 2.
Press the XFINITY key to check that your
remote controls your set-top box. If it does,
you’re all set. If not, repeat these steps but
press C for Cisco mode or A for XFINITY
mode in step B.
Once the code is correctly entered, your
XFINITY Remote is paired with the device.
B
A
C
Program Your Remote To Control Your
Set-Top Box
4 Pair Remote for “Aim Anywhere” Control
Control your cable box without having to point at it, even when it is inside a
cabinet or entertainment center.
Aim Anywhere is only supported on certain XFINITY cable boxes. To see if your
cable box supports Aim Anywhere control visit xnity.com/remotes
Press the Setup button until the All Power key
on the remote changes from red to green.
Press the XFINITY button.
Follow the on-screen instruction to enter the
3-digit code that appears.
Once the code is correctly entered, your
XFINITY Remote is paired with the device.
B
A
C
Need to remove Aim Anywhere control? Press
and hold the Setup but ton on the rem ote until the
status LED changes from red to green. Press A on
the remote. If th e status LED blinks green twice,
you have successfully removed Aim Anywhere.
?
Not working? Make sure to install batteries in th e
remote, check that your TV is on and that you are
entering the cor rect 3-digit code on your TV screen .
?
5 Control Your TV’s Power and Volume
Press and hold the Setup button (about 3
seconds) until the Status LED changes from
red to green.
B
Using the list on the right, nd the rst
5-digit code for your TV manufacturer.
A
Enter in the rst 5-digit code for you TV
manufacturer. The Status LED should blink
green twice.
C
Verify that the code was accepted by using
your remote to adjust volume and turn the
TV on and o.
D
Not working? Try the second code listed. Still
not working? Visit xnity.com/remotes for a
complete list of codes or use the My Account
app for mobile (iOS/Android) or X1.
Popular TV Manufacturer Codes
Emerson 11864, 10171
Insignia 12049, 11641
JVC 11774, 12321
LG 12731, 10178
Magnavox 10054,12597
Panasonic 114 80 , 10051
Philips 118 67, 12597
RCA 10047, 11447
Samsung 12051, 10702
Sanyo 1015 4 , 1114 2
Sharp 10093, 12360
Sony 10810, 11685
Tos hiba 1015 6, 11524
VIZIO 11758, 12707
Westinghouse 11712, 13579
If your code isn’t listed or you would
like to control an audio device, visit
xnity.com/remotes
FCC Compliance Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not used in accordance with
the instructions, may cause harmful interference to
radio communications.
There is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between
the equipment and receiver.
• Connect the equipment into an outlet on a
circuit dierent from that which the receiver is
connected.
• Consult the dealer or an experienced remote
control/ TV technician for help.
• It is strongly recommended that the TV be
plugged into a separate wall outlet.
The user is cautioned that changes and modications
made to this equipment without the approval of
the manufacturer could void the user’s authority to
operate this equipment. This device complies with
part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may
not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
To Next Page
Need help?
General
