Remote not working with your T V?
The remote has to be programmed
to the TV and/or audio receiver to
control power, volume, and input. Go
to the Remote Settings screen on X1
to program control of your TV and
audio receiver.
Need help? Say “Remote help” to see
tips & tricks for using your remote.
Voice command not working? Make
sure you’re pressing the Voice button
while you speak into the remote, and
relea se it when complete.
Need to pair with another box? If
you want to use your remote with a
dierent set-top box repeat s tep 3
while pointing the remote at the box.
Looking for more information? Visit
Xnity.com/remotes for additional
help with Xnity remotes
Voice Remote
Start
FCC Compliance Statement
1 Meet Your Remote
2 Turn On Your Remote 3 Pair Your Remote for Voice Control Troubleshooting
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rul es. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not use d
in accordance wi th the instructions, may caus e
harmful interference to radio communications.
There is no guar antee that interference will not
occur in a particular installation. If this equipment
does cause harmful inter ference to radio or
television reception, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increa se or decrease the separation
between the equipment and receiver.
• Connec t the equipment into an outlet on a
circui t dier ent from that which the receiver
is connected.
• Consult the dealer or an experienced remote
control / TV technician for help.
• It is strongly recommende d that the TV be
plugged into a separate wall outlet.
The user is cautioned that changes and modications
made to this equipment without the approval of the
manufacturer could void the user’s author ity to
operate this equipment.
This device complies with part 15 of the FCC rules.
Operation is subject to the following t wo conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCC ID: MG3-4352
Mic / Status LED
Pick up your remote and remove
the “Pull” tab on the back by
pulling up on the tab. The Status
LED will blink green four times
as the remote powers up (about 5
seconds).
Make sure your TV and set-top
box are turned on.
A
B
B
C
Your remote arrives with the AA batteries already installed, but not
activated. Here is how to power it on for the rst time.
Press and hold the Xnity but ton
and Info button until the status
LED changes from red to green
(about 5 seconds).
You should see the an on-screen
conrmation when the remote
is paired. If you do not see
conrmation, press the Xnity
button again.
Once your remote is paired, follow
the on-screen instructions to set
up power, volume, and input control
for your TV.
A
Use Voice Control to search for networks and shows, set DVR recordings,
and get recommendations.
Voice Control
Push and hold to talk .
Discover content by
channel, program or
key words.
Save
Star ts recording the
program you are watching
or saves future programs
to your DVR.
Info
Displays information
about programs and
notications.
TV Input
Changes to the next
available input on your T V.
Number Keys
Use predictive text ( T9) to
quickly search for content.
XFINITY / Menu
Access Guide, S aved,
XFINITY On Demand, Apps,
Search, and Settings.
Back Arrow
Press and release for Last.
Press and hold for 2
seconds to Exit.
Power
Now that your remote is set up,
press and hold the Voice button to
ask “what can i say?” for some voice
command suggestions.
Pairing
Successful
To Next Page
Need help?
General
