Start
XR2
Xnity Remote
TV Power
XFINITY / Me nu
Access Guide , Saved,
XFINITY On Demand, Apps,
Search and Settings.
Search
Discover content by
channel, pr ogram or
key words.
TV Input
Changes to th e next
availabl e input on your T V
(if progr ammed in Step 4)
All Power
Setup
Program r emote for Aim
Anywhe re or to control yo ur
TV or audio d evice.
Swap
Switches b etween tw o DVR
tuners so y ou can control
playback o f two channels .
Number Keys
1 Meet Your Remote 2 Turn On Your Remote
Install bat teries in the remote an d turn on your devices.
Turn on your TV.B
To set up your remote, rs t install AA batter ies
(sold separate ly). The All Power key will blink
green four time s as the remote powers up
(abo ut 5 se conds) .
A
Turn on your cable box.C
Back
3
Your remote is prepr ogrammed to operate X FINITY cable boxes. I f you are
using the remo te for control of a non-XFINI TY cable box, you may ne ed to
program the r emote for the Motorola o r Cisco mode. Follow the ste ps below to
program your remote.
Press the Setup butto n until the All Power key
on the remote chan ges from red to green.
Press B for control of a Motor ola brand
cable box; press C for control of a Cisco
or Scientic-At lanta brand cable box .
Note: If you need to r e-program the remo te
for control of an XFI NITY cable box, rep eat
the steps abov e and press A in step 2.
Press the XFINIT Y key to check that your
remote controls yo ur set-top box. If it does ,
you’re all set . If not, repeat these s teps but
press C for Cisco mode or A for X FINITY
mode in step B.
Once the code is corr ectly entered, your
XFINITY Rem ote is paired with the devi ce.
B
A
C
Program Your Remote To Control Your
Set-Top Box
4 Pair Remote for “Aim Anywhere” Control
Control your ca ble box without having to p oint at it, even when it is in side a
cabinet or entertainment center.
Aim Anywh ere is only supporte d on certain XFINIT Y cable boxes. To see if your
cable box suppo rts Aim Anywher e control visit xni ty.com/remotes
Press the Setup butto n until the All Power key
on the remote chan ges from red to green .
Press the XFINIT Y button.
Follow the on- screen instructi on to enter the
3-digit code that ap pears.
Once the code is corr ectly entered, your
XFINITY Rem ote is paired with the devi ce.
B
A
C
Need to remo ve Aim Anyw here contro l? Press
and hold the S etup button on the r emote until th e
status LE D changes fro m red to green. Press A on
the remote . If the stat us LED blinks green twice,
you have successfully removed Aim Anywhere.
?
Not working? Make sure to instal l batterie s in the
remote, che ck that your T V is on and that yo u are
entering t he correct 3 -digit cod e on your TV sc reen.
?
5 Control Your TV’s Power and Volume
Press and hold t he Setup button (about 3
seconds) until the St atus LED changes from
red to green.
B
Using the list on th e right, nd the rst
5-digit co de for your TV manufa cturer.
A
Enter in the rst 5- digit code for you TV
manufac turer. The Status LED should b link
green twice .
C
Verify tha t the code was accepted by using
your remote to adjus t volume and turn the
TV on and o.
D
Not working? Try the second code listed. Still
not working? Visit xnity.com/remotes for a
complete list of codes or use the My Account
app for mobile (iOS/Android) or X1.
Popular TV Manufacturer Codes
Emerson 11864, 10171
Insignia 12049, 11641
JVC 11774, 12321
LG 1273 1, 1017 8
Magnavox 10054,12597
Panasonic 11 48 0, 1 00 51
Philips 118 67, 12 597
RCA 10047, 11447
Samsung 12051, 10702
Sanyo 101 54 , 11142
Sharp 10093, 12360
Sony 10810, 11685
Tosh iba 10 156, 1152 4
VIZIO 11758, 12707
Westinghouse 11712, 13579
If your code isn’ t listed or you would
like to control an audio d evice, visit
xnity.com/remotes
FCC Compliance Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not used in accordance with
the instructions, may cause harmful interference to
radio communications.
There is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between
the equipment and receiver.
• Connect the equipment into an outlet on a
circuit dierent from that which the receiver is
connected.
• Consult the dealer or an experienced remote
control/ TV technician for help.
• It is strongly recommended that the TV be
plugged into a separate wall outlet.
The user is cautioned that changes and modications
made to this equipment without the approval of
the manufacturer could void the user’s authority to
operate this equipment. This device complies with
part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may
not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
To Next Page
Need help?
General
