11
CHANGE
SB CODE 001
f to confirm the Simplebus code change, press OK;
f press ESC to exit.
» if present, the indirect Simplebus code for that user will
be displayed, to modify it press CANC and enter the new
number using the alphanumeric keypad:
CHANGE INDIRECT
CODE 000001
f to confirm the indirect code change, press OK;
STORING IN
MEMORY...
f press ESC to exit.
U12 How to use the lock-release
f The external unit electric lock can be controlled by
pressing
; if the command is carried out, some
confirmation tones will be emitted.
U13 Day/night operating mode
The porter switchboard has two operating modes:
• DAY mode
• NIGHT mode
In DAY mode, all calls originating from the external unit are
received by the switchboard, which can transfer them to the
internal units as necessary.
In NIGHT mode, the switchboard intercepts calls from the
external unit, only if they are directed to the switchboard
(code 240). Calls directed to the internal units appear on the
display, but are not intercepted by the switchboard.
The operating mode may be activated in 2 dierent ways:
• manually, using the DAY/NIGHT key
.
f Press
to change the operating mode immediately.
» The operating mode is indicated on the display:
• DAY with the symbol: (_ _)
• NIGHT is indicated with the text NIGHT.
CAUTION! NIGHT mode is only available if there is
a main external unit.
• in automatic mode (programming performed by the
installer, see ”I3 - Day/night automatic mode”).
The text AUTO will only appear during operation during
the DAY. During operation in automatic mode, DAY/NIGHT
modes can be switched manually (
); in this case,
automatic mode is excluded and reactivated at the next
programmed switching time.
U14 How to activate the “Follow me” function (available
from R.I.006)
This function can be used to divert calls for the switchboard
to local or remote telephones.
f To activate this function, press and hold the DAY/NIGHT
key
for at least 3 sec., until the display shows:
FOLLOW ME
ACTIVE
f To disable it, repeat the procedure so that the initial screen
appears on the display:
A
D
(_ _) 14:40
WED 12/03/10
» Once a call has been made, the switchboard will ring until
the remote device begins communicating; the call can be
answered from the switchboard by cancelling the “Follow
me” function.
CAUTION! To use this function, telephone switchboard
Art. 2906 and interface Art. 2912 must be fitted. Contact
your usual installer. Contact your usual installer.
This function can only activated for the switchboard set as
secondary (see ”C8.3 - Type of switchboard (Simplebus
Top mode) (available from R.I.006)”).
U15 Alarm signalling (available from R.I.006)
The switchboard can receive alarm signals transmitted by
internal units in any operating status (call or conversation).
When the switchboard receives an alarm:
» an alarm sounds. The signal may be silenced by pressing
any of the buttons on the switchboard.
» the alarm signal for the first user that activated the alarm
appears on the display:
ALARM (04)
USER 002
» the signal disappears when the internal unit answers the
switchboard call (to make the call, press ), or when the
switchboard operator forces a deletion process using the
CANC key.
If several alarm situations occur simultaneously, an alarm
code is created using the same methods as described in the
section ”U6 How to call an internal unit listed in the call
log” and only the number of alarms recorded will appear on
the display (10 max).
» When a call is received from an external or internal unit,
the switchboard exits alarm status so that the incoming
call can be dealt with correctly. Once the call has been
dealt with, alarm status is restored.
U16 How to activate an additional relay Art. 1256
(e.g. to activate the following independently and with
a specific command: lights, CCTV alarm contacts,
driveway gates, entrances without external units or
other devices) (available from R.I.006)
Actuators can be activated in standby mode and during
conversation with an external unit.
To activate the actuator:
f press
, you will be asked to enter the code to activate a
specific actuator. If there is no code a generic actuator will
be activated;
ACTUATOR
CODE:
f to confirm actuator activation, press .
To Next Page
Loading...