EasyManua.ls Logo

Craftsman C459-52415 - User Manual

Craftsman C459-52415
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
CAUTION: Before using this
product, read this manual
and follow all safety rules
and operating instructions.
Operator’s Manual
• SAFETY
• ASSEMBLY
• OPERATION
• MAINTENANCE
• PARTS LIST
®
PRINTED IN U.S.A.
FOR CUSTOMER ASSISTANCE CALL 1-800-668-1238
769-09968
06/11/14
TWO STAGE SNOW THROWERS
Model Nos. C459-52413 (24”)
C459-52415 (28”)

Table of Contents

Questions and Answers

  • N
    nicholaswilsonAug 6, 2025
    Why does my Craftsman C459-52415 engine fail to start?
    • J
      Jacqueline LesterAug 6, 2025
      Your Craftsman Snow Blower engine may fail to start due to several reasons: * The choke might not be in the CHOKE position. Move the choke to the CHOKE position. * The spark plug wire could be disconnected. Connect the wire to the spark plug. * The fuel tank might be empty or contain stale fuel. Fill the tank with clean, fresh gasoline. * The engine might not be primed. Prime the engine as instructed. * The spark plug could be faulty. Clean, adjust the gap, or replace it. * The key may not be fully inserted into the ignition switch. Insert the key fully into the switch.
  • C
    calvin92Aug 10, 2025
    What to do if my Craftsman C459-52415 unit fails to discharge snow?
    • G
      Greg GardnerAug 10, 2025
      If your Craftsman Snow Blower fails to discharge snow, it could be due to the following reasons: * The chute assembly may be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool or a stick. * A foreign object might be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool or a stick. * Shear pins might be sheared. Replace them with new shear pins.
  • P
    palexanderAug 14, 2025
    Why is my Craftsman Snow Blower engine running erratically?
    • C
      Chase MillerAug 14, 2025
      An erratic engine in your Craftsman Snow Blower can stem from: * The engine running on CHOKE. Move the choke lever to the RUN position. * Stale fuel. Replace with clean, fresh gasoline. * Water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel.
  • K
    Kimberly BrownAug 19, 2025
    What causes loss of power in my Craftsman C459-52415?
    • N
      Nicole BrockAug 19, 2025
      Loss of power in your Craftsman Snow Blower may be due to: * A loose spark plug wire. Connect and tighten the spark plug wire. * A plugged gas cap vent hole. Remove any ice and snow from the gas cap, ensuring the vent hole is clear.
  • J
    Jason Hurst DVMAug 23, 2025
    What to do if my Craftsman C459-52415 Snow Blower has excessive vibration?
    • F
      fhardyAug 23, 2025
      If your Craftsman Snow Blower has excessive vibration, it may be due to loose parts or a damaged auger. Stop the engine immediately, disconnect the spark plug wire, and tighten all bolts and nuts. If vibration continues, have the unit serviced by an authorized Service Center.
  • P
    paula16Aug 27, 2025
    What to do if my Craftsman Snow Blower unit fails to propel itself?
    • J
      Joseph CurryAug 27, 2025
      If your Craftsman Snow Blower unit fails to propel itself, the drive control cable may need adjustment. Refer to the Maintenance & Adjustments section for how to adjust the drive control cable.
  • N
    nicholas64Sep 1, 2025
    How to fix Craftsman Snow Blower chute that doesn't rotate easily?
    • I
      isaaccolemanSep 1, 2025
      If the chute fails to easily rotate 180 degrees on your Craftsman Snow Blower, it may be assembled incorrectly. Unassemble the chute control and reassemble as directed in the Assembly & Set-up section.

Summary

Safe Operation Practices

General Safety and Preparation

Read manual, understand controls, prepare area, and follow instructions.

Gasoline Handling and Machine Operation Safety

Safe practices for fueling, storing, operating, and avoiding hazards.

Assembly & Set-Up

Handle, Chute, and Component Installation

Instructions for assembling handles, chute, and related components.

Controls and Features

Operation

Starting, Stopping, and Engaging Machine

Procedures for starting the engine, engaging drive, and augers.

Service

Belt Replacement

Step-by-step guide for replacing the auger and drive belts.

Friction Wheel Service

Troubleshooting

Engine and Performance Issues

Common engine and machine problems and their solutions.

Warranty Information

Craftsman C459-52415 Specifications

General IconGeneral
Engine Displacement208cc
Drive TypeSelf-Propelled
Auger MaterialSteel
Skid ShoesAdjustable
Warranty2-Year Limited
Clearing Width24 inches
Intake Height21 inches
Speed6 forward, 2 reverse
Starting SystemElectric start
Engine Type4-Cycle

Related product manuals