EasyManua.ls Logo

Craftsman CMXGBAM 795756 - User Manual

Craftsman CMXGBAM 795756
56 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
CAUTION
Before using this equipment, read the manual and follow all safety rules and operating instructions.
CRAFTSMAN® is a registered trademark of Stanley Black & Decker, Inc., used under license.
CRAFTSMAN® est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence
© 2018 CRAFTSMAN U.S. & Canada Only
CRAFTSMAN.com
Form No. 769-15958
(July 19, 2018)
INSTRUCTION MANUAL | GUIDE D’UTILISATION
SNOW BLOWER
Model Nos. CMXGBAM 795756
CMXGBAM 795757
CMXGBAM 795758
CMXGBAM 795759
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.
1-888-331-4569 WWW.CRAFTSMAN.COM
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the model depicted may differ
from yours. The terms “snow thrower” and “snow blower” may be used interchangeably for this product.

Table of Contents

Questions and Answers

  • S
    Sally LopezAug 15, 2025
    What to do if my Craftsman CMXGBAM 795756 is not throwing snow?
    • M
      Michaela BennettAug 16, 2025
      If your Craftsman Snow Blower isn't discharging snow, consider these possibilities: * The chute assembly might be clogged. Stop the engine immediately, disconnect the spark plug wire, and clean the chute assembly and inside of the auger housing with a clean-out tool. * A foreign object could be lodged in the auger. Stop the engine immediately, disconnect the spark plug wire, and remove the object from the auger with a clean-out tool. * The auger cable may need adjustment. Adjust the auger control cable according to the Assembly section. * The auger belt might be loose or damaged. Replace the auger belt, referring to the Service and Maintenance section. * The shear pins could be sheared. Replace them with new shear pins, as detailed in the Operation section.
  • R
    Richard RomeroAug 20, 2025
    Why is my Craftsman CMXGBAM 795756 engine running erratically?
    • C
      courtneyharrisonAug 20, 2025
      An erratic engine in your Craftsman Snow Blower can stem from several causes: * The engine may be running on CHOKE; move the choke control to the RUN position. * The fuel may be stale; fill the tank with clean, fresh gasoline. * There might be water or dirt in the fuel system; drain the fuel tank by running the engine until it stops, then refill with fresh fuel. * The carburetor may be out of adjustment or the engine over-governed; in either case, contact a qualified service dealer for repair.
  • M
    michaelawilsonAug 23, 2025
    What to do if my Craftsman CMXGBAM 795756 Snow Blower has loss of power?
    • P
      patrick75Aug 25, 2025
      If your Craftsman Snow Blower is experiencing a loss of power: * Check if the spark plug wire is loose; connect and tighten the spark plug wire. * See if the gas cap vent hole is plugged; remove any ice and snow from the gas cap, ensuring the vent hole is clear.
  • C
    candice01Aug 27, 2025
    Why does my Craftsman CMXGBAM 795756 plow snow instead of blowing it?
    • J
      johnsoncarlAug 27, 2025
      Your Craftsman Snow Blower might plow snow instead of blowing it due to: * Low/slow ground speed in wet/slushy snow 1-3” deep; increase ground speed and always operate the engine at FULL throttle. * Shear pins sheared; replace with new shear pins as instructed in the Operation section.
  • K
    Kelly SpencerAug 31, 2025
    Why is my Craftsman Snow Blower vibrating excessively?
    • O
      ogilesAug 31, 2025
      Excessive vibration in your Craftsman Snow Blower could be due to loose parts or a damaged auger or impeller. Stop the engine immediately, disconnect the spark plug wire, and tighten all bolts and nuts. If the vibration continues, have the unit serviced by a Repair Center.
  • C
    Carla JimenezSep 4, 2025
    What to do if my Craftsman CMXGBAM 795756 Snow Blower won't move forward?
    • S
      Susan FrancisSep 4, 2025
      If your Craftsman Snow Blower fails to propel itself, it could be due to: * Drive cable in need of adjustment; adjust the drive control cable, referring to the Service and Maintenance section. * Drive belt loose or damaged; contact a qualified service dealer for repair using an identical replacement part. * Worn friction wheel; have the friction wheel replaced by a qualified service dealer using an identical replacement part.
  • W
    William MontgomerySep 7, 2025
    Why does the chute on my Craftsman CMXGBAM 795756 not rotate easily?
    • M
      Matthew HuntSep 7, 2025
      If the chute on your Craftsman Snow Blower fails to easily rotate 180-200 degrees, it may be assembled incorrectly. Disassemble the chute control and reassemble as directed in the Assembly section.
  • J
    Janet FigueroaNov 11, 2025
    Why won't my Craftsman CMXGBAM 795756 Snow Blower engine start?
    • E
      elizabeth84Nov 12, 2025
      There are several reasons why your Craftsman Snow Blower engine might fail to start: * The choke control may not be in the CHOKE position, so move the choke control to the CHOKE position. * The spark plug wire might be disconnected; connect the wire to the spark plug. * The spark plug could be faulty; clean, adjust the gap, or replace it. * The fuel tank may be empty or the fuel stale; fill the tank with clean, fresh gasoline. * The engine may not be primed; prime the engine as instructed in the Operation section. * The safety key might not be inserted; insert the safety key fully into the switch. * The extension cord might not be connected (when using the electric start button); connect one end of the extension cord to the electric starter outlet and the other end to a thre...

Craftsman CMXGBAM 795756 Specifications

General IconGeneral
Engine Power208cc
Clearing Width24 inches
Intake Height21 inches
Auger MaterialSteel
Drive SystemSelf-propelled
Throwing Distance40 ft
Start TypeRecoil
StagesTwo-Stage

Related product manuals