Craftsman CMXGKAM1158708

Questions and Answers

A
Amanda SmithAug 18, 2025
Why won't my Craftsman CMXGKAM1158708 Edger start?
- S
  Sara HillAug 18, 2025
  If your Craftsman Edger engine fails to start, there are several potential causes: * The blade control may be disengaged, so ensure it is engaged. * The spark plug boot might be disconnected; connect the wire to the spark plug boot. * The fuel tank could be empty or contain stale fuel; refill with clean, fresh gasoline. * The engine may not be primed (if equipped with a primer); prime it as instructed in the Operation section. * The spark plug could be faulty; clean, adjust the gap, or replace it. * The engine might be flooded; wait a few minutes before restarting. * The fuel line could be blocked; contact an authorized service center to have it cleaned.
F
Frank MilesAug 20, 2025
What to do if the drive belt slips on my Craftsman Edger?
- L
  Lisa JacksonAug 20, 2025
  If your Craftsman Edger drive belt is slipping, it is likely that the belt is worn or stretched. Replace the drive belt.
L
Lynn BellAug 23, 2025
Why my Craftsman Trimmer engine fails to start?
- I
  Ivan StricklandAug 23, 2025
  Several factors can cause a Craftsman Trimmer engine to fail to start. Here are some possible causes and solutions: * Ensure the blade control is engaged. * Check if the spark plug boot is disconnected and connect it. * Refill the fuel tank with clean, fresh gasoline if it's empty or the fuel is stale. * If your trimmer has a primer, prime the engine as instructed in the Operation section. * Inspect the spark plug; clean, adjust the gap, or replace it if faulty. * If the engine is flooded, refer to the Engine Operator’s Manual.
N
Nicholas BestAug 26, 2025
How to fix a Craftsman Edger that idles poorly?
- V
  Vicki CrosbyAug 26, 2025
  If your Craftsman Edger idles poorly, try the following: * Reset the gap or replace the spark plug if it's fouled, faulty, or the gap is too wide.
D
Diana CohenAug 28, 2025
What to do if Craftsman Trimmer has excessive vibration?
- P
  Patrick OneillAug 28, 2025
  If you're experiencing excessive vibration with your Craftsman Trimmer, it could be due to: * A bent or damaged edger blade, which would need replacement. * A bent or damaged blade spindle, which requires inspection by an authorized service center.
R
rgoodwinAug 30, 2025
Why is my Craftsman CMXGKAM1158708 Edger engine running rough?
- A
  Amber FordAug 30, 2025
  If your Craftsman Edger engine runs erratically, check the following: 1. Ensure the spark plug boot is securely connected and tightened. 2. Replace stale fuel with clean, fresh gasoline. 3. Clear any blockage in the vent of the gas cap. 4. If there is water or dirt in the fuel system, run the engine until it stops due to lack of fuel, then refill with fresh fuel. 5. If the fuel line is blocked, contact an authorized service center to have it cleaned.
S
Scott DominguezSep 2, 2025
What causes excessive vibration in my Craftsman CMXGKAM1158708 Edger?
- L
  Leonard JohnsonSep 2, 2025
  If your Craftsman Edger is vibrating excessively, it could be due to: * A bent or damaged edger blade. Replace the blade. * A bent or damaged blade spindle. Contact an authorized service center to have the unit inspected.
Z
zrodriguezSep 4, 2025
Why is my Craftsman Edger overheating?
- A
  Amy GravesSep 4, 2025
  If your Craftsman Edger engine is overheating, it could be due to: * Low engine oil level. Fill the crankcase with the proper oil. * Restricted airflow. Clean the area around and on top of the engine.
D
Denise CarterSep 7, 2025
What causes occasional skips in a Craftsman CMXGKAM1158708?
- A
  Andrew WilliamsSep 7, 2025
  Adjust the gap of the spark plug if it's too close.
P
Phillip HunterSep 9, 2025
Why does my Craftsman Trimmer engine run erratic?
- J
  jennifer49Sep 9, 2025
  If your Craftsman Trimmer engine runs erratically, here are a few things to check: * Make sure the spark plug boot is securely connected and tightened. * Replace stale fuel with clean, fresh gasoline. * Clear any blockage in the vent of the gas cap. * If there is water or dirt in the fuel system, run the engine until it stops due to lack of fuel, then refill with fresh fuel.

Summary

Safety Instructions

General Safety Warnings

Key warnings and responsibilities for safe operation of the machine.

California Proposition 65

Warning about chemicals in engine exhaust and vehicle components.

General Operation Safety

Safe practices for operation, including operator zone, area inspection, and attire.

Safety Instructions

Children Safety

Precautions to protect children from hazards related to lawn edgers.

Gasoline Handling Safety

Safe procedures for handling, fueling, and storing gasoline.

General Service Safety

Safety measures for performing maintenance and inspections.

Safety Instructions

Engine Modification Warning

Discourages tampering with engine settings and governor for safety.

Emissions Notice

Information regarding EPA and California emissions compliance.

Safety Symbols Explained

Description of graphical symbols indicating hazards and precautions.

Spark Arrestor Information

Details on spark arrestor requirements and availability.

Assembly

Handle Assembly

Steps for attaching and securing the main handle to the unit.

Control Cable Routing

Instructions for properly routing the control cable.

Securing Control Cable

Method for attaching the control cable to the handle assembly.

Assembly

Blade Depth Control Cable

Securing the cable that controls the blade depth.

Starter Rope Guide Installation

Installing the guide for the engine's starter rope.

Bevel Adjustment Setup

Adjusting the blade angle for different edging types.

Know Your Edger

Blade and Control Levers

Description of primary controls like blade control and depth lever.

Adjustment Levers Explained

Details on curb height and bevel adjustment levers.

Starting Mechanism

How to operate the recoil starter and primer.

ANSI Safety Compliance

Statement of adherence to American National Standards Institute (ANSI).

Operation

Stopping the Engine

Procedure to safely stop the engine and blade.

Starting the Engine

Step-by-step guide for igniting the engine.

Edging Technique

Instructions on how to perform the edging operation effectively.

Operation

Curb Edging Adjustment

How to adjust the wheel for edging along curbs.

Beveling the Edge

Setting the blade angle for creating beveled edges.

Trenching Functionality

Using the optional feature for creating trenches.

Service and Maintenance

Maintenance Schedule Overview

Table outlining recommended service intervals and tasks.

General Maintenance Advice

Recommendations for general upkeep, warranty, and adjustments.

Engine Care and Cleaning

Instructions for cleaning and maintaining the engine.

Lubrication Guide

Points and frequency for lubricating wheels and pivot points.

Service and Maintenance

Bearing Block Lubrication

Procedure for lubricating the bearing block.

Edger Blade Care and Inspection

How to inspect, care for, and service the edger blade.

Drive Belt Replacement

Step-by-step instructions for replacing the drive belt.

Service and Maintenance

Off-Season Storage Procedures

Guidelines for storing the equipment during the off-season.

Engine Storage Preparation

Steps to prepare the engine for long-term storage.

Edger Storage Preparation

Steps to prepare the edger unit for storage.

Troubleshooting

Engine Starting Problems

Common issues and remedies for engine failure to start.

Engine Performance Issues

Solutions for erratic running, overheating, and operational skips.

Operational Problems

Addressing vibration, belt slip, and poor idling.