Crane BARNES SITHE 4SCM Series User Manual

A Crane Co. Company
IMPORTANT! Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
 changeproductwithoutpriorwrittennotication.
420 Third Street 83 West Drive, Bramton
Piqua, Ohio 45356 Ontario, Canada L6T 2J6
Phone: (937) 778-8947 Phone: (905) 457-6223
Fax: (937) 773-7157 Fax: (905) 457-2650
www.cranepumps.com
Form No. 130642S-Rev. K
28 Frame
4SCM
Monovane Pumps
20 - 100HP, 1750RPM
20 - 30HP, 1150RPM
4SCD
Dual Vane Pumps
20 - 60HP, 1750RPM
20 - 40HP, 1150RPM
6SCM
Monovane Pumps
20 - 60HP, 1750RPM
20 - 25HP, 1150RPM
6SCD
Dual Vane Pumps
20 - 125HP, 1750RPM
20 - 40HP, 1150RPM
8SCD
Dual Vane Pumps
25 - 60HP, 1750RPM
20 - 40HP, 1150RPM
10 - 15HP, 870RPM
8SCT
Tri-Vane Pumps
20 - 60HP, 1750RPM
20 - 40HP, 1150RPM
10 - 30HP, 870RPM
10SCD
Dual Vane Pumps
25 - 40HP, 1150RPM
10 - 30HP, 870RPM
INSTALLATION and OPERATION MANUAL
Submersible Chopper Pump
This product may be covered by one or more of the following
patents and other patent(s) pending: NZ DSN NO. 424412,
NZ DSN NO. 424413, AUS DSN NO. 201812608,
AUS DSN NO. 201812609, EU Design Reg. 005293040-0001

Crane BARNES SITHE 4SCM Series Specifications

General

Brand	Crane
Model	BARNES SITHE 4SCM Series
Category	Water Pump
Language	English

Summary

SAFETY FIRST!

General Hazard Categories

Describes electrical, mechanical, pressure, and chemical hazards.

Safe Operating Practices

Covers proper installation, operation, and maintenance precautions.

Specific Safety Warnings

Addresses clothing, lifting, securing, and material handling safety.

GENERAL INFORMATION

Pump Receiving and Storage

Inspecting pump upon receipt and proper storage procedures.

INSTALLATION

Location, Submergence, and Discharge

Pump placement, submergence, and piping requirements.

Liquid Level and Electrical Setup

Level controls, wiring, grounding, and power cord handling.

WIRING DIAGRAMS AND PROTECTION

Three Phase AC Wiring Configurations

Details wiring for different voltage configurations and sensors.

Motor Overload and Start Protection

Explains overload protection and manual start switch requirements.

START-UP PROCEDURES

Pre-Operation Checks

Verifying voltage, phase, rotation, and moisture sensor tests.

Post-Connection Checks and Reports

Insulation tests, pump-down tests, and start-up report completion.

PREVENTATIVE MAINTENANCE

Routine Inspections and Tests

Maintenance for oil, seals, impeller, moisture sensors, and insulation.

SERVICE AND REPAIR

Impeller, Volute, and Seal Procedures

Detailed steps for servicing pump components.

REPLACEMENT PARTS

Ordering and Identification Guidelines

Information required for ordering and identifying parts.

TROUBLESHOOTING

Common Pump Operation Problems

Diagnosing issues like no run, no shutoff, humming, and low capacity.

Cycling, Overloads, and Noise Issues

Troubleshooting frequent cycling, thermal overloads, and vibrations.

WARRANTY INFORMATION

Warranty Terms and Exclusions

Details coverage, period, exclusions, and limitations.

Claims, Registration, and Returns

Procedures for warranty claims, registration, and merchandise returns.

START-UP REPORT

General and Pre-Startup Checks

Recording owner details, nameplate data, and initial checks.

Operational and Submersible Checks

Verifying noise, vibration, leaks, flow, and submersible specific items.