EasyManuals Logo

Crate VFX5112,VFX5212 User Manual

Crate VFX5112,VFX5212
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
Important Information About Tubes and Tube Products (continued):
Survival Tips For T
ube Amplifiers:
To prolong tube life, observe these tips and recommendations:
• Match the impedance of your speaker cabinet(s) to your amplifier. Improper impedance matching will con-
tribute to early tube degradation and may cause premature tube failure.
• Make sure the speaker(s) are properly connected prior to turning on the amplifier.
After playing the amplifier, allow sufficient time for it to properly cool down prior to moving it. A properly
cooled amplifier prolongs tube life due to the internal components being less susceptible to the damage
caused by vibration.
Allow the amplifier to warm up to room temperature before turning it on. The heat generated by the tube
elements can crack a cold glass housing.
• Replace the output tube(s) before the performance degrades or the tubes fail completely. Replace the
tube(s) on a regular basis (at least once per year or as often as every 4 to 6 months if you play long and
hard every day).
Always have the bias checked after replacing the output tubes (unless the amplifier is equipped with "self-
biasing circuitry"). This should be done ONLY at a qualified service center. Improper biasing could result
in the tubes running too hot, which greatly reduces the life of the tubes – or too cold, which results in dis-
torted sound regardless of level settings. Do not play the amplifier if it exhibits these symptoms – get the
bias checked/adjusted immediately to prevent tube failure and/or other damage.
• If the locating notch on the base of a power tube breaks off, replace the tube. This significantly reduces
the risk of damaging your amplifier by incorrectly inserting the tube.
• Protect the amplifier from dust and moisture. If liquid gets into the amplifier proper, or if the amplifier is
dropped or otherwise mechanically abused, have it checked out at an authorized service center before
using it.
• Proper maintenance and cleaning in combination with routine checkups by your authorized service center
will insure the best performance and longest life from your amplifier.
CAUTION: Tube replacement should be performed only by qualified service personnel who are
familiar with the dangers of hazardous voltages that are typically present in tube circuitry.
9
VFX5112/5212 Guitar Amplifier

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Crate VFX5112,VFX5212 and is the answer not in the manual?

Crate VFX5112,VFX5212 Specifications

VFX 5112

Power IconPower
output power rating50 Watts RMS
power requirements120 VAC, 60 Hz, 200VA
Sound IconSound
signal to noise ratio70 dB
gain channel A62 dB
gain channel B98 dB
Equalization IconEqualization
EQ Channel A Treble30 dB range @ 10 kHz
EQ Channel A Mid6 dB range @ 600 Hz
EQ Channel A Low30 dB range @ 80 Hz
EQ Channel B Treble10 dB range @ 4 kHz
EQ Channel B Mid10 dB range @ 1 kHz
EQ Channel B Low12 dB range @ 100 Hz
presence18 dB range @ 20 kHz
Speaker Specifications IconSpeaker Specifications
speaker configuration1 X 12”
speaker power60 W
speaker impedance16 ohm
Size and Weight IconSize and Weight
width23 inches
height19 inches
depth10 inches
weight48 lbs

VFX 5212

Power IconPower
output power rating50 Watts RMS
power requirements120 VAC, 60 Hz, 200VA
Sound IconSound
signal to noise ratio70 dB
gain channel A62 dB
gain channel B98 dB
Equalization IconEqualization
EQ Channel A Treble30 dB range @ 10 kHz
EQ Channel A Mid6 dB range @ 600 Hz
EQ Channel A Low30 dB range @ 80 Hz
EQ Channel B Treble10 dB range @ 4 kHz
EQ Channel B Mid10 dB range @ 1 kHz
EQ Channel B Low12 dB range @ 100 Hz
presence18 dB range @ 20 kHz
Speaker Specifications IconSpeaker Specifications
speaker configuration2 X 12”
speaker power60 W
speaker impedance8 ohm
Size and Weight IconSize and Weight
width28 inches
height21 inches
depth11 inches
weight58 lbs

Related product manuals