Creda FLORIDA PLUS - User Manual

Questions and Answers

S
sfloresAug 14, 2025
What to do if the Creda FLORIDA PLUS Plumbing Product shower cycles from hot to cold?
- B
  Brett WhiteAug 14, 2025
  If your Creda Plumbing Product shower is cycling from hot to cold, it might be because the temperature is set too high, causing the thermal cut-out to activate. Try turning knob 'C' clockwise to increase water flow. Then, slowly increase the water temperature by turning knob 'C' anti-clockwise until you reach a comfortable temperature. Remember to wait about 20 seconds after each adjustment to see the effect. You may also need to select the 'HALF HEAT' setting.
M
Mrs. Leah RosalesAug 17, 2025
What to do if Creda FLORIDA PLUS water is too HOT?
- K
  Kelly ElliottAug 17, 2025
  If the water from your Creda Plumbing Product is too hot, increase the water flow by adjusting knob 'C' clockwise. You may also need to select the 'HALF HEAT' setting. Additionally, ensure that the water supply flow is sufficient by fully opening the service valve or stop cock. Check the hose for any kinks that might be restricting water flow, and clean the shower handset.
K
Katie SnyderAug 20, 2025
What to do if Creda FLORIDA PLUS Plumbing Product water goes cold while using shower?
- T
  Teresa JohnsonAug 20, 2025
  If the water from your Creda Plumbing Product goes cold while you're showering, first check that the neon light is on. Also, make sure the water pressure hasn't dropped significantly, which could cause the pressure switch to cut out (for example, if another tap is using water). Try raising the position of the shower handset.
B
Breanna RogersAug 25, 2025
What to do if Creda FLORIDA PLUS water is too HOT (Professional Service)?
- N
  Nicole FloydAug 25, 2025
  If the water from your Creda Plumbing Product is too hot and requires professional service, it could be due to restricted water flow, possibly caused by a blockage in the filter of the solenoid valve. Switch off the water, loosen the inlet connection to the solenoid, and replace it.
R
rkelleyAug 27, 2025
What to do if Creda FLORIDA PLUS Plumbing Product water is too COLD?
- A
  Anna WilliamsAug 27, 2025
  If the water from your Creda Plumbing Product is too cold, first, check that the power is on and the neon light is illuminated. Then, decrease the water flow by adjusting knob 'C' anti-clockwise. You may also need to select the 'FULL HEAT' setting.
M
Melissa ShahAug 30, 2025
Why does Creda Plumbing Product water take longer to heat up?
- J
  Justin MartinAug 30, 2025
  If your Creda Plumbing Product water is taking longer to heat up, it's possible the thermal cut-out activated during previous use, and the 'overheat' light is still on. The unit will automatically reset when it cools down. You may also need to select the 'FULL HEAT' setting.
H
hinesnatalieSep 3, 2025
How to fix poor spray pattern on Creda Plumbing Product?
- D
  Dean BurtonSep 3, 2025
  To fix a poor spray pattern on your Creda Plumbing Product, clean the shower handset.
J
Joseph FranklinSep 6, 2025
What causes water to discharge from the pressure relief valve in Creda Plumbing Product, and how to fix it?
- D
  David BurkeSep 6, 2025
  If water is discharging from the pressure relief valve of your Creda Plumbing Product, check for and eliminate any causes of high pressure. Also, check for blockages on the outlet, such as a blocked shower handset. You can replace the pressure relief disc, but note that it is not covered by the guarantee.
B
Barbara BrownSep 9, 2025
How to fix Creda FLORIDA PLUS with no control over water flow?
- A
  Ashley StewartSep 9, 2025
  To fix a Creda Plumbing Product with no control over water flow, undo the headworks of the stabiliser valve. Check that the stabiliser is in place and remove any debris in the valve.