Crestron DM-RMC-200-C DigitalMedia 8G+™ Receiver 200
A single cable connects the DM-RMC-200-C to a DM
®
switcher or transmitter (each
sold separately), transporting video, audio, control, and networking signals through
one RJ-45 connection.
1
Multiple DM-RMC-200-Cs may be installed to handle each
display in a multi-room distribution system, all fed from a central DM switcher. Or, a
single DM-RMC-200-C can be fed straight from a DM 8G+ transmitter, affording a
simple solution for extending a computer or AV signal to a single display.
High-Definition Scaler
Through a distributed scaler approach, DigitalMedia delivers the most flexible and
user-friendly solution for routing multiple disparate sources to many different
display devices. Employing DM receivers with built-in scaling, DM allows an
independent high-performance scaler to be installed at every display device, ensuring
an optimal image on every screen. Distributed scaling allows a high-definition 3D or
high-resolution computer source to be viewed on lower resolution 2D displays
without compromising the original signal.
The DM-RMC-200-C accepts any video source from standard NTSC 480i to HD
1080p60 with Deep Color, as well as computer sources from VGA to
UXGA/WUXGA, and scales them perfectly to match the native resolution of your
video display. A range of common output resolutions is supported to work with
virtually any popular flat-panel display, projector, or computer monitor. Intelligent
frame rate conversion enables support for 24p and PAL format sources, and
3D-to-2D conversion allows 3D content to be fed simultaneously to separate 3D
and 2D displays. Setup and use of the scaler is simplified through fully automatic
operation utilizing the display’s EDID.
2, 3
Video Wall Processing
The DM-RMC-200-C also provides zoom capability on its output to display just a
portion of the source image. Using this feature, multiple units may be combined to
configure a high-definition video wall composed of up to 16 individual displays.
Configurations of 2x2, 3x2, 3x3, 4x3, or 4x4 are supported, and all that is required is
a separate DM-RMC-200-C for each display, and a DM switcher with sufficient
DM 8G+ outputs.
Audio Amplifier
The DM-RMC-200-C is equipped with stereo analog audio outputs, and a built-in
30 Watt stereo amplifier. The output volume is adjustable via a control system using
a keypad, touch screen, or handheld remote. The amplifier provides plenty of power
to drive a pair of local speakers, or use the line output to connect directly to an input
on the display device, a pair of amplified speakers, or a local AV receiver, amplifier,
or sound system.
1. For DM 8G+ wiring up to 330 feet (100 meters) between devices, use Crestron DM-CBL-8G
DigitalMedia 8G cable, Crestron DM-CBL DigitalMedia cable, Crestron DM-CBL-D DigitalMedia D
cable, or generic CAT5e (or better) UTP or STP. Shielded cable and connectors are recommended to
safeguard against unpredictable environmental electrical noise which may impact performance at
resolutions above 1080p. Refer to the latest version of the Crestron DigitalMedia Infrastructure Guide
(Doc. 4556) for complete wiring guidelines and to the Crestron DigitalMedia Design Guide (Doc.
4789) for complete system design guidelines. All cable sold separately.
2. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D-to-2D conversion if display device does not support 3D.
3. EDID (Extended Display Identification Data) is data embedded in an HDMI, DVI, or VGA signal that
enables a display device to tell the source device what resolutions and formats it can support, allowing
the source to configure itself automatically to feed the best signal that both devices can support.
Operations & Installation Guide – DOC. 7126B DigitalMedia 8G+™ Receiver 200: DM-RMC-200-C • 3
To Next Page
Loading...
Need help?
General
Weight and Dimensions
