Crown 1200 - Q42871-6 Output Module

Micro-Tech 1200 Amplifier Service Manual
25
CAPACITORS
C01 C 8511-5 .047µF
C02 C 7964-7 .22µF
C03 C 7964-7 .22µF
C04 C 8534-7 .0047µF
C05 C 8534-7 .0047µF
C06 C 6806-1 .01µF
C07 C 6807-9 .001µF
C08 C 6810-3 180pF
C09 C 6809-5 220pF
C43 C 6806-1 .01µF
DIODES
D01 C 2851-1 1N4004
D02 C 2851-1 1N4004
D03 C 2851-1 1N4004
D04 C 2851-1 1N4004
D05 C 2851-1 1N4004
D06 C 2851-1 1N4004
D07 C 2851-1 1N4004
D08 C 2851-1 1N4004
D09 C 2851-1 1N4004
D10 C 2851-1 1N4004
D11 C 2851-1 1N4004
D12 C 2851-1 1N4004
INDUCTORS
L00 C 6592-6 Output Coil
L01 C 3510-2 470µH
L02 C 3510-2 470µH
TRANSISTORS
Q17 C 3810-6 MPSA43
Q19 C 3578-9 MPSA93
RESISTORS
R00 A10266-7501 75
R01 A10266-4711 470
R02 C 7778-1 5.6 FP
R03 C 6486-2 .2 5W
R04 C 6486-2 .2 5W
R05 C 6486-2 .2 5W
R06 C 6486-2 .2 5W
R07 C 6486-2 .2 5W
R08 C 6486-2 .2 5W
R09 C 7779-9 22 FP
R10 A10266-4711 470
R11 A10266-2R73 2.7 1W
R12 A10266-1204 12 2W
R13 A10266-7501 75
R14 A10266-1204 12 2W
R15 C 6486-2 .2 5W
R16 C 6486-2 .2 5W
R17 C 6486-2 .2 5W
R18 C 6486-2 .2 5W
R19 C 6486-2 .2 5W
R20 C 6486-2 .2 5W
R21 C 7778-1 5.6 FP
R22 C 7779-9 22 FP
R23 C 6844-2 250 Pot
R24 A10266-1331 13K
R25 A10266-2221 2.2K
R26 C 6844-2 250 Pot
R27 A10266-3911 390
R28 A10266-1331 13K
R29 A10266-5101 51
R30* A10265-10201* 102*
R35 A10266-1204 12 2W
R36 A10266-1204 12 2W
R37 A10266-1204 12 2W
R38 A10266-1204 12 2W
R39 A10266-1204 12 2W
R40 A10266-1204 12 2W
MISC
Board P10305-4
Jumpers C 5868-2 0 Ohm (7)
Clips D 6414-3 Q17/Q19
Beads C 8341-7 Q17/Q19
J500 J600 C 7057-0 10 Pin HDR
Note: R30 is 102 Ohms in most units, though in
some cases a different value may be used to match
the installed S100/S200 LM334 (C5826-0) device
grade. This is the standard value and is used with
the most common LM334 grade, green. If the
LM334 is marked with a blue dot, R30 should be a
107 Ohm resistor (A10265-10701); if it is marked
with a yellow dot then R30 should be a 100 Ohm
resistor (A10265-10001).
Q42871-6 Output Module (P10305-4 board) Parts List