To Next PageTo Next Page
Need help?Do you have a question about the Cub Cadet Pro Z 900 Series and is the answer not in the manual?
Read manual, learn controls, and ensure operators are trained before use. Owner is responsible for training.
Follow all instructions, know controls, keep bystanders clear, inspect area, and use approved accessories.
Exercise caution on slopes, mow across, not up/down. Use low speeds and avoid sudden changes in direction.
Keep children away from operating area and machine. Never let children under 16 operate.
Do not tow heavy loads on slopes. Use a machine with a hitch and follow manufacturer recommendations.
Use care when loading/unloading. Ensure ramps are stable and secured. Secure machine properly.
Understand the ROPS and seat belt system. Ensure they are properly installed, used, and maintained.
Handle hydraulic fluid with care. Escaping fluid can cause injury. Relieve pressure before work.
Use extreme care when handling fuel. It is flammable and vapors are explosive. Extinguish all ignition sources.
Understand and follow all safety symbols and instructions on the machine and in the manual.
List of items included in the product packaging for assembly and setup.
Required tools and initial steps before assembling the mower, like removing packaging.
Instructions for engaging transmission bypass levers/rods to move the mower manually.
Procedure for adjusting the ROPS from transport to operation position.
How to adjust the steering column tilt for operator comfort and visibility.
Instructions for installing the steering wheel, avoiding impact tools.
Steps for installing the operator's seat, including securing the seat and bracket.
Adjusting the lumbar support lever to vary lower back support for the operator.
Adjusting the height of the arm rests by rotating the knob under the arm rest.
Controlling seat tilt by turning the knob rearward to tilt back or forward to tilt forward.
Adjusting seat height using the air ride system and height adjustment lever.
Moving the seat forward or backward using the seat adjustment rod.
Recommended tire inflation pressures for front and rear tires.
Refer to Product Care section for checking lubrication and grease points.
Procedure for connecting positive and negative battery cables correctly.
Engaging and disengaging transmission bypass for manual movement.
Understanding the positions (OFF/STOP, ON, START) of the ignition switch.
Operating the PTO knob to engage/disengage the engine's electric PTO clutch.
Recording operating hours for maintenance scheduling and tracking service alerts.
Using the manual throttle control to maintain uniform engine speed.
Controlling engine speed and RPM with the electronic throttle lever.
Using the choke for starting and understanding the MIL indicator light.
Engaging and releasing the parking brake lever.
Operating the forward drive pedal to control mower movement and speed.
Operating the reverse drive pedal to control mower movement and speed.
Location and proper use of fuel tank caps.
Adjusting the operator's seat forward or rearward using the adjustment lever.
Controlling the seat tilt forward or backward using the knob.
Adjusting arm rest height using the knobs located under the seat arms.
Adjusting the mechanical suspension for operator weight.
Adjusting lumbar support on the seat back using the lever.
Locking and unlocking the self-leveling seat mechanism.
Using the seat prop to hold the seat forward for access.
Securing the seat into its operating position using the latch.
Understanding the deck height index for adjusting cutting height.
Using the deck lift pedal or switch to raise and lower the mowing deck.
Locking the mower deck in the transport position.
Function of the transmission oil expansion reservoir and its level.
Adjusting the steering column tilt for operator comfort and visibility.
Location of the cup holder between the fuel tank and control panel.
Understanding ROPS positions: TRANSPORT, TRANSPORT WITH BAGGER, OPERATION.
Location and function of fuel gauges for measuring fuel level.
Operating fuel valves to control fuel flow from tanks or shut off flow.
Location of receptacles for optional accessories on the RH console.
Operating the three-way switch for lights: OFF, Beacon ON, or Beacon & Work ON.
Positioning the beacon light assembly upright and securing it.
Using the 12V outlet for accessories with a maximum load of 5A at 12V.
Information on front wheel weights and the warning to not operate without them.
Understanding the safety interlock system and its prevention of operation.
Step-by-step procedure for starting the engine, including safety precautions.
Starting procedure for manual throttle/choke or EFI engines.
Starting procedure for electronic throttle/EFI engines.
Ensuring correct oil viscosity and battery charge for cold weather starting.
Procedure for jump starting a mower with a booster battery, with safety warnings.
How to operate the forward drive pedal for smooth and stable mower movement.
Techniques for turning the mower while moving forward, including safe practices.
Safe operation for driving the mower in reverse, including looking behind.
How to steer the mower while driving in reverse.
Maneuvering the mower for a zero-turn action using pedals and steering wheel.
Procedure for safely stopping the mower's motion and engine.
Guidelines for safe operation on slopes, including angle limits and turning.
Steps to engage the PTO and start the mower deck.
Proper use of the mower deck, including clearing debris and avoiding premature wear.
Information on different types of mower blades and their applications.
Procedures after each operation to extend mower life and ensure safety.
Rinsing grass clippings from deck underside to prevent buildup and corrosion.
Cleaning debris from deck top, spindle covers, and belt area.
Step-by-step guide for changing the engine oil, including safety precautions.
Periodically lubricating all pivot points with a quality lubricating oil.
Checking tire air pressure and guidelines for proper inflation and maintenance.
Safety precautions and general information regarding battery handling and care.
Maintaining battery terminals and cables to protect against corrosion.
Procedures for storing the mower battery for extended periods.
Step-by-step guide for removing the battery from SD model mowers.
Step-by-step guide for removing the battery from SDL model mowers.
Engaging and disengaging transmission bypass rods for manual movement.
Checking oil level for Parker hydrostatic transmissions.
Checking and changing oil for Hydro-Gear hydrostatic transmissions.
Preparing the mower for storage, including location and protective measures.
Steps to take to prepare the mower for use after storage.
Procedure for removing the mower deck from the machine.
Steps for removing and reinstalling front tires on the mower.
Instructions for removing and replacing the PTO belt.
Instructions for removing and replacing the deck belt.
Procedure for safely removing and reinstalling mower blades.
Guidelines for properly sharpening mower blades to maintain balance and edge.
Steps for removing and replacing the mower deck spindle assembly.
Common problems, their causes, and recommended remedies for minor service issues.
Instructions for checking and adjusting mower deck level side-to-side and front-to-back.
Procedure for leveling the mower deck side-to-side for optimal cutting.
Procedure for setting the proper blade pitch (front-to-back) for the mower deck.
Adjusting front gauge wheels to ensure they are clear of the ground at the set height.
Recharging the battery after storage and recommended charge rates.
Specific charging instructions for lead-acid batteries.
Specific charging instructions for AGM batteries, do not use automotive chargers.
Procedure for jump starting the mower with jumper cables, with safety warnings.
Location and identification of fuses, relays, and the power distribution module.
Troubleshooting the electric PTO clutch if blades do not turn.
Step-by-step instructions for removing and replacing rear tires.
Daily checks for PTO, parking brake, and seat switches for safety interlock function.
Details the warranty coverage for defects in materials and workmanship.
Table outlining warranty periods for various product types and components.
Notes on prorated warranties, frames, mowing decks, and other specific components.
Exclusions from the limited warranty, including damage due to misuse or lack of maintenance.
Information on implied warranties, remedy limitations, and risk assumption.
General
