EasyManuals Logo

Cybex Platinum CLOUD Z i-SIZE User Manual

Cybex Platinum CLOUD Z i-SIZE
252 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #19 background imageLoading...
Page #19 background image
19
DEENIT
ADJUSTING TO BODY SIZE REGOLAZIONE IN BASE ALLA CORPORATURA
The headrest has to be adjusted in a way that the distance between
the child‘s shoulders and the headrest doesn‘t exceed 2 cm
(approx. 2 fingers width).
Check the height of the Harness Straps: Position the Harness
Straps at or just below the child‘s shoulders for rear-facing use.
Pull the adjustment handle (4) upwards to unlock the headrest (3).
Now you can adjust the headrest.
Il poggiatesta deve essere regolato in modo che la distanza tra le
spalle del bambino e la base del poggiatesta sia al massimo 2 cm
(ovvero circa lo spessore di due dita).
Controllare l’altezza delle cinture: posizionarle all’altezza delle spalle
del bambino o appena al di sotto, per l’uso contro il senso di marcia.
A tale fine tirare in alto la leva di regolazione (4) per sbloccare il
poggiatesta (3). A questo punto è possibile regolare il poggiatesta.
Adjusting the Headrest Regolazione del poggiatesta
NOTE!
The shoulder belts are firmly connected to the headrest and do
not have to be adjusted separately.
NOTA BENE!
Le cinture per le spalle sono fissate al poggiatesta e non
devono essere regolate separatamente.
NOTE!
The headrest (3) ensures the best possible protection for your
child only if it is adjusted to the optimum height. There are 11 height
positions that can be set.
NOTA BENE!
Il poggiatesta (3) garantisce la protezione ottimale per il
bambino soltanto se regolato all’altezza corretta. Può essere fissato in
11 (undici) posizioni diverse.
NOTE!
The newborn inlay protects your child. It must be used up to size
of 60 cm.
NOTA BENE!
Il riduttore per neonati porotegge il bambino. Dev’essere
utilizzato fino a quando il bambino raggiunge un’altezza di almeno 60cm.
Removing the Newborn Inlay Rimuovere gli inserti
The newborn inlay (5) may be removed after the baby is
61 cm (approx. 3 months) to provide more space for the child. To
remove the newborn inlay (5) open and remove the shoulder pads. Then
remove the newborn inlay and place the shoulder pads back on the
shoulder belts.
L’inserto neonato (5) può essere rimosso dopo che il bambino ha
superato i 61 cm (3 mesi circa), per fornire maggiore spazio di seduta.
Per togliere l’inserto neonato (5) aprire e rimuovere i cuscinetti delle
cinture per le spalle. Rimuovere il riduttore e mettere nuovamente i
cuscinettu sulle cinture per le spalle.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cybex Platinum CLOUD Z i-SIZE and is the answer not in the manual?

Cybex Platinum CLOUD Z i-SIZE Specifications

General IconGeneral
Weight4.8 kg
Age rangeFrom birth up to approx. 24 months
Recline PositionsLie-flat position outside the car
Side Impact ProtectionIntegrated Linear Side-impact Protection (L.S.P. System)
FeaturesIntegrated Linear Side-impact Protection (L.S.P. System)
InstallationISOFIX
Dimensions67 x 44 x 38 cm
Rotation180° when used with Base Z
Headrest11-position adjustable
Harness5-point
UpholsteryMachine washable fabric covers
Height range45 – 87 cm
Safety standardi-Size (ECE R129)
Child weightUp to 13 kg

Related product manuals