cytiva AKTA flux s User Manual (English)

Questions and Answers:

C
Christopher MaciasAug 5, 2025
Why is there little or no flow in my Cytiva Laboratory Equipment?
- S
  Sarah ReedAug 5, 2025
  If you experience little or no flow in your Cytiva Laboratory Equipment, verify that the connected inlet is the one being used. Ensure liquid is supplied to the system and check the inlet containers. Confirm that the pressure control valve is open. Inspect the tubing from the inlet container for any issues like excessive length, small internal diameter, narrow sections, or blockages. Also, check the peristaltic tubing for wear, flattening, or improper tension within the pump head; re-tension or replace the tubing as needed.
A
Anthony WilliamsAug 10, 2025
What to do if the feed outlet pressure is too high in cytiva AKTA flux s Laboratory Equipment?
- T
  Tabitha HarrisAug 10, 2025
  If the feed outlet pressure is too high in your Cytiva Laboratory Equipment, first check the outlet to ensure the sensor isn't blocked. Also, the filter cassette might be clogged with particulates. If so, replace the cassette and filter the feed material with a 0.2-micron filter before concentrating the protein.
K
Kaitlyn JohnsonAug 17, 2025
How to fix an automatic circuit breaker that has triggered in cytiva AKTA flux s Laboratory Equipment?
- H
  heather40Aug 18, 2025
  If an automatic circuit breaker has triggered in your Cytiva Laboratory Equipment, turn off the instrument and visually inspect it for damage. If you notice any damage, contact Cytiva. Check if any of the automatic fuses have popped out and push them back in.
J
Julie HernandezAug 23, 2025
What to do if the pump is not working in cytiva AKTA flux s Laboratory Equipment?
- C
  Charles ThomasAug 23, 2025
  If the pump is not working in your Cytiva Laboratory Equipment, check if the Stop button on the main screen has been pressed. If the problem persists, contact Cytiva.
D
Darren RamirezAug 29, 2025
How to replace a blown fuse in cytiva AKTA flux s Laboratory Equipment?
- R
  Roberto Fuller MDAug 29, 2025
  If a replaceable fuse has blown in your Cytiva Laboratory Equipment, check the replaceable fuses in the fuse drawer at the power input. If a fuse is broken, replace it with one of the correct rating. Refer to the Electric power section on page 184 for fuse specifications. After replacing the fuse, turn on the system. If the problem continues, contact Cytiva.

cytiva AKTA flux s Specifications

General

UV Monitoring	Yes
Pressure Range	Up to 6 bar
Control	UNICORN software
Operating Temperature	4°C to 40°C
pH Range	2 to 12
UV Detection Wavelength	280 nm
Power Requirements	100-240 V, 50/60 Hz
Temperature Control Range	5 to 40 °C (optional)

Summary

1 Introduction to ÄKTA flux s

1.1 Important User Information

Provides critical information for safe operation, intended use, and prerequisites.

1.2 About This Manual

Explains the purpose, scope, and typographical conventions used in the manual.

1.3 Associated Documentation

Lists related user documentation and software help resources for the system.

1.4 Additional User Documentation and Specific Documentation

Details system-specific documentation and component documentation for ÄKTA flux s.

1.5 Abbreviations Used in Documentation

Defines abbreviations used throughout the ÄKTA flux s user documentation.

2 Safety Instructions for ÄKTA flux s

2.1 Safety Precautions

Outlines general, personal, and environmental safety precautions for operating the system.

2.2 System Labels and Symbols

Describes the system label and other safety or regulatory labels attached to the product.

2.3 Emergency Procedures

Provides instructions for emergency shutdown and restarting the system after power failure.

3 System Description of ÄKTA flux s

3.1 Illustrations of ÄKTA flux s Components

Provides visual identification of front and rear views of the ÄKTA flux s system.

3.2 System Control Interface

Explains how the system is controlled via the operator touchscreen and main screen.

3.3 Standard Equipment Overview

Details the standard components of the ÄKTA flux s system.

3.4 Optional Equipment for ÄKTA flux s

Describes optional components that can be installed to enhance system functionality.

3.5 Filter Devices for ÄKTA flux s

Provides a description and overview of filter types that can be installed with the system.

3.6 Process Flowchart Illustration

Presents a flowchart detailing the process components and pressure sensors.

4 Flow Lines in ÄKTA flux s

4.1 Recirculation Loop Description

Explains the recirculation loop, including feed and retentate lines, flow control, and DeltaP.

4.2 Permeate Line Functionality

Describes the permeate line, its flow control, and recycling capabilities.

4.3 Transfer Line Setup

Details the transfer line, which requires an optional transfer pump for operation.

5 Installation of ÄKTA flux s

5.1 Site Requirements and Preparation

Summarizes power supply, environmental, and positioning requirements for installation.

5.2 Unpacking the ÄKTA flux s

Provides requirements for receiving, storing, and safety precautions during unpacking.

5.3 Transporting the ÄKTA flux s

Outlines important information and requirements for safely transporting the system.

5.4 Setting Up the ÄKTA flux s

Guides through the steps required to set up the ÄKTA flux s before initial use.

5.5 Installation Test Procedures

Lists the performance tests that must be conducted after the system installation.

6 Run Preparations for ÄKTA flux s

6.1 Filter Installation Procedures

Contains general information on where and how to install different filter types on the system.

6.2 Installing Kvick Lab Packet and Holder

Provides instructions for installing Kvick Lab packet holders with filters onto the system.

6.3 Filter Testing Procedures

Details pre-process procedures like filter integrity and leakage tests before product processing.

6.4 Calibration Procedures

Describes procedures for calibrating pumps, pressure sensors, and tank level for accuracy.

7 Operation of ÄKTA flux s

7.1 Starting the System

Guides through the initial steps and precautions for starting the ÄKTA flux s system.

7.2 Performing a Run

Details the procedures for performing basic filtration and automated features.

7.3 Procedures After Completing a Run

Outlines essential steps to empty, clean, and prepare the system after operation.

8 Settings and Configuration

8.1 USB Device Management and Software Update

Covers generating system health reports, managing USB devices, and updating software.

8.2 Configuring Alarms Screen

Explains how to set up system warnings and alarms for various parameters.

8.3 Configure System Screen Settings

Allows users to configure system parameter units like pressure, temperature, and flow rates.

8.4 Calibration Settings Screen

Interface for calibrating pumps, pressure sensors, and tank level.

8.5 System Information Screen

Displays installed software, running hours, and optional components status.

8.6 Setting System Set-points

Guides on how to adjust set-points for various system parameters like flow and level.

9 Maintenance of ÄKTA flux s

9.1 User Maintenance Schedule

Provides recommendations for routine and periodic maintenance tasks.

9.2 Sanitization and Cleaning Procedures

Details methods for sanitization and cleaning-in-place (CIP) of the system.

9.3 Storage Procedures

Describes procedures for both short-term and long-term storage of the system.

9.4 Repair and Calibration Guidance

Provides information on component repair and calibration, advising to contact support.

9.5 Replacing the Mains Fuse

Step-by-step instructions for safely replacing the main fuse of the instrument.

10 Troubleshooting Guide

11 Reference Information

11.1 System Specifications

Lists technical specifications including dimensions, weight, volume, and sound levels.

11.2 Software License Information

Details the software components and their associated license agreements.

11.3 Wetted Materials in ÄKTA flux s

Lists materials used in manufacturing and standard components that contact process fluids.

11.4 Chemical Resistance Guidelines

Provides allowed exposure concentrations and times for chemicals used with the system.

11.5 Recycling and Disposal Information

Describes procedures for decontamination, disposal, and recycling of the equipment.

11.6 Regulatory Information

Lists directives and standards fulfilled by the ÄKTA flux s system.

11.7 Ordering Information and Contact Details

Provides contact details and website for ordering information and spare parts.

11.8 Health and Safety Declaration Form

Form for service personnel and customers to declare equipment is clean and safe for access.

Related product manuals

cytiva AKTA pilot 600

206 pages

cytiva AKTA readyflux

cytiva VIA Thaw L1000

108 pages

cytiva BPG 300 Columns

146 pages

cytiva ReadyToProcess WAVE 25