D-Link DES-3052P - Page 180

DES-3028 DES-3028P DES-3028G DES-3052 DES-3052P Layer 2 Fast Ethernet Switch CLI Reference Manual
175
Example usage:
To display all of the currently configured access profiles on the Switch:
DES-3028P:4#show access_profile
Command: show access_profile
Access Profile Table
================================================================================
Profile ID: 101 Type: IPv4 Frame Filter - ICMP
================================================================================
Masks Option
VLAN Source IP Dest. IP DSCP Prot
---------------- --------------- --------------- ---- ----
20.0.0.0 10.0.0.0 ICMP
================================================================================
Total Profile Entries: 1
Total Used Rule Entries: 0
Total Unused Rule Entries: 256
DES-3028P:4#
create cpu access_profile
Purpose
Used to create an access profile specifically for CPU Interface Filtering on the Switch and to
define which parts of each incoming frame’s header the Switch will examine. Masks can be
entered that will be combined with the values the Switch finds in the specified frame header
fields. Specific values for the rules are entered using the config cpu access_profile command,
below.
Syntax
create cpu access_profile <value 1-3> [ethernet {vlan | source_mac <macmask> |
destination_mac <macmask> | 802.1p | ethernet_type} | ip {vlan | source_ip_mask
<netmask> | destination_ip_mask <netmask> | dscp | [icmp {type | code} | igmp { type } |
tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff> | flag_mask [ all |
{urg | ack | psh | rst | syn | fin}] } | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask
<hex 0x0-0xffff>} | protocol_id_mask <hex 0x0-0xff> {user_define <hex 0x0-0xffffffff>}]}|
packet_content_mask {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> | offset_16-31<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff><hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>}]
Description
The create cpu access_profile command is used to create an access profile used only for CPU
Interface Filtering. Masks can be entered that will be combined with the values the Switch finds in
the specified frame header fields. Specific values for the rules are entered using the config cpu
access_profile command, below.
Parameters
ethernet  Specifies that the Switch will examine the layer 2 part of each packet header.
 vlan  Specifies that the Switch will examine the VLAN part of each packet header.
 source_mac <macmask>  Specifies to examine the source MAC address mask.
 destination_mac <macmask>  Specifies to examine the destination MAC address mask.
 802.1p  Specifies that the Switch will examine the 802.1p priority value in the frame’s
header.
 ethernet_type  Specifies that the Switch will examine the Ethernet type value in each