DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide
46
Feature Detailed Description
• DEM-310GT (1000BASE-LX, Single-mode, 10 km)
• DEM-311GT (1000BASE-SX, Multi -mode, 550 m)
• DEM-312GT2 (1000BASE-SX, Multi-mode, 2 km)
• DEM-314GT (1000BASE-LHX, Single-mode, 50 km)
• DEM-315GT (1000BASE-ZX, Single-mode, 80 km)
• DGS-712 (1000BASE-TX)
Supports to following WDM transceivers:
• DEM-302S-BXD/BCU (1000BASE-BX, Single-mode, 2 km)
• DEM-330T/R (1000BASE-BX, Single-Mode, 10 km)
• DEM-331T/R (1000BASE-BX, Single-Mode, 40 km)
SFP+ Ports
Compliant with the following standards:
• IEEE 802.3ae compliance
• IEEE 802.3z compliance
Supports to following SFP/WDM transceivers:
• All supported SFP/WDM transceivers will work in SFP+ ports
Supports to following SFP+ transceivers:
• DEM-431XT-DD (10GBASE-SR SFP+ Transceiver, 80 m:
OM1 & OM2 MMF 300 m: OM3 MMF)
• DEM-431XT (10GBASE-SR SFP+ Transceiver (w/o DDM), 80
m: OM1 & OM2 MMF 300 m: OM3 MMF)
• DEM-432XT-DD (10GBASE-LR SFP+ Transceiver, 10 km)
• DEM-432XT (10GBASE-LR SFP+ Transceiver (w/o DDM), 10
km)
• DEM-433XT-DD (10GBASE-ER SFP+ Transceiver, 40 km)
• DEM-433XT (10GBASE-ER SFP+ Transceiver (w/o DDM), 40
km)
• DEM-434XT (10GBASE-ZR SFP+ Transceiver (w/o DDM), 80
km)
• DEM-436XT-BXU (10GBASE-LR BiDi SFP+ Transceiver (w/o
DDM), 20 km, TX: 1270 nm, RX: 1330 nm)
• DEM-436XT-BXD (10GBASE-LR BiDi SFP+ Transceiver (w/o
DDM), 20 km, TX: 1330 nm, RX: 1270 nm)
Supports to following SFP+ Direct Attached Cables (DAC):
• DEM-CB100S-10-GbE (SFP+, 1 m, Direct Attach Cable), for
stacking
• DEM-CB300S-10-GbE (SFP+, 3 m Direct Attach Cable), for
stacking
• DEM-CB700S-10-GbE (SFP+, 7 m Direct Attach Cable), for
stacking
PoE Ports
(DGS-1510-28P, DGS-1510-
28XMP, and DGS-1510-
52XMP Only)
Supports the following:
• IEEE 802.3af PoE and IEEE 802.3at PoE+ compliance
• Power (ports 1 to 24) to PD devices up to 15.4 Watt per port
(802.3af) or 30 Watt per port (802.3at) and more sufficiently is
able to provide power to PD devices
• The auto-discovery feature automatically recognizes the
connection of the PD device and immediately provides power
• Automatically disable ports if the port current is over 600mA
while. Other ports will remain active
• Active circuit protection automatically disables the port if there
is a short while other ports remain active
To Next Page
Loading...
