Need help?Do you have a question about the Danfoss VLT AutomationDrive FC 361 Series and is the answer not in the manual?
General| Category | DC Drives |
|---|---|
| Communication Protocols | Modbus RTU |
| Enclosure Rating | IP20 |
| Protection Features | Overvoltage, Undervoltage, Short Circuit |
| Ambient Temperature Range | -10°C |
Outlines the intended audience and technical information provided in the guide.
Lists other available resources for drive functions and programming.
Details the manual and corresponding software version.
Covers CE Mark, Low Voltage Directive, and EMC Directive compliance.
Explains symbols, formatting, and conventions used in the document.
Defines the warning, caution, and notice symbols used.
Defines requirements for personnel authorized to install or operate the equipment.
Provides essential safety warnings regarding high voltage and discharge time.
Details the power ratings, enclosure sizes, weights, and dimensions.
Describes features like short-circuit protection, overvoltage protection, and phase detection.
Highlights features for enhanced system performance: AMA, PID controller, thermal protection.
Explains methods for slowing down the motor using AC or DC brake.
Details the cooling concept for improved reliability and component life.
Describes available fieldbus devices for efficient communication.
Details functional extension options like I/O modules and encoder inputs.
Provides detailed electrical data for enclosures J8 and J9.
Details mains supply voltage, frequency, and drop-out behavior.
Specifies motor output voltage, frequency, and torque characteristics.
Defines environmental conditions, humidity, and temperature limits.
Lists maximum cable lengths and cross-sections for control and power cables.
Details specifications for digital and analog inputs/outputs.
Provides weights for enclosure sizes J8 and J9.
Contains detailed exterior and terminal dimensions for J8 and J9 enclosures.
Guidelines for storing the drive in a dry location.
Provides instructions and warnings for safely lifting the drive unit.
Details requirements for environments, including condensation and extreme temperatures.
Lists available mounting configurations and considerations for proper installation.
Explains cooling requirements, airflow rates, and clearance.
Covers automatic and manual derating for high temperatures and altitudes.
General safety instructions for electrical installation.
Provides a basic wiring schematic for the drive.
Details power connections, cable shielding, and length.
Explains control cable routing, grounding, and terminal functions.
Lists recommended fuse sizes and explains disconnect switch requirements.
Covers motor connection, thermal protection, and parallel motor configurations.
Discusses RCD usage and requirements for protective grounding.
Explains leakage current generation and mitigation strategies.
Provides guidance for using the drive with isolated mains sources.
Details drive efficiency calculation and factors affecting it.
Lists typical acoustic noise values for different enclosure sizes.
Explains dU/dt effects on motor service life and provides test results.
Describes interference types and EMC principles.
Provides instructions for achieving an EMC-compliant installation.
Discusses harmonics, their effects on power systems, and related standards.
Provides an overview of the drive's assemblies and internal functions.
Explains processes for controlling and regulating the motor.
Details how the drive receives input sources for control.
Describes speed control and torque control in open-loop mode.
Explains control types requiring feedback for speed or process control.
Covers control structures in VVC+ mode and internal current control.
Illustrates the components of a typical closed-loop drive system.
Shows wiring for speed control using analog voltage or current references.
Provides wiring configurations for basic start/stop commands.
Details wiring for external alarm reset functionality.
Explains wiring for motor thermal protection using a thermistor.
Shows encoder wiring and explains direction determination.
Explains how to use the online configurator to select drives.
Lists ordering numbers for functional extensions and kits.
Glossary of abbreviations and symbols used in the manual.
Provides definitions for technical terms and concepts.
Details RS485 bus installation, cabling, and termination.
Explains the FC protocol, telegram formats, and drive setup.
Describes the structure of FC protocol telegrams.
Provides examples of writing and reading parameter values via FC protocol.
Introduces the Modbus RTU protocol and its communication process.
Details the FC control profile, including control word and status word bits.
Explains the bits within the FC control word for drive operation.
Describes the status word bits indicating drive operational states.
Explains how speed reference values are transmitted via bus.
Details the control word bits for PROFIdrive profile commands.
Explains the status word bits for PROFIdrive profile states.
To Next Page