What should I do if my Danfoss DC Drives experience a mains failure?
If your Danfoss DC Drives experience a mains failure, it indicates that the supply voltage to the frequency converter is lost. Check the fuses to the frequency converter and mains power supply to the unit.
What does parameter error mean on Danfoss VLT AutomationDrive FC 302?
If your Danfoss DC Drives displays a parameter error, it means the parameter is out of range.
What to do if Danfoss VLT AutomationDrive FC 302 says 'AMA parameter out of range'?
If you receive an 'AMA parameter out of range' error on your Danfoss DC Drives, check the settings.
What to do if motor phase V is missing in Danfoss DC Drives?
If your Danfoss DC Drives report that motor phase V is missing, remove the power from the frequency converter and check motor phase V.
What to do for option detection issues in Danfoss DC Drives?
If your Danfoss DC Drives detects a change in the option layout, enable option layout changes to apply the change.
What to do if option configuration has changed in Danfoss VLT AutomationDrive FC 302 DC Drives?
If the option configuration has changed in Danfoss DC Drives, it means one or more options have either been added or removed since the last power-down. Check that the configuration change is intentional and reset the unit.
What causes 10 Volts low error in Danfoss DC Drives?
A '10 Volts low' error in Danfoss DC Drives can be caused by a short in a connected potentiometer or improper wiring of the potentiometer. Remove the wiring from terminal 50. If the warning clears, the problem is with the customer wiring. If the warning does not clear, replace the control card.
How to troubleshoot motor thermistor overtemp in Danfoss VLT AutomationDrive FC 302?
If you are getting a motor thermistor overtemp warning on your Danfoss DC Drives, check whether the thermistor is disconnected. Also, check for motor overheating and if the motor is mechanically overloaded. When using terminal 53 or 54, ensure the thermistor is correctly connected between either terminal 53 or 54 (analog voltage input) and terminal 50 (+10 V supply), and that the terminal switch for 53 or 54 is set for voltage. If using terminal 18, 19, 31, 32, or 33 (digital inputs), ensure the thermistor is correctly connected between the digital input terminal used (digital input PNP only) and terminal 50.
What to do for an inrush fault in Danfoss VLT AutomationDrive FC 302 DC Drives?
If your Danfoss DC Drives are showing an inrush fault, it means too many power-ups have occurred within a short time period. Let the unit cool to operating temperature.
Why Danfoss VLT AutomationDrive FC 302 power on with red light?
If your Danfoss DC Drives show 'Power On' and the indicator is red, this typically indicates an IP Address Conflict. Resolve the IP conflict.
General| Category | DC Drives |
|---|---|
| Control Method | Flux Vector Control |
| Communication Options | CANopen, PROFIBUS |
| Cooling | Forced convection |
| Enclosure | IP20, IP21, IP55, IP66 |
| Protection Class/Rating | IP20 |
| Protection Features | Overvoltage, Undervoltage, Overcurrent, Overtemperature, Short Circuit |
| Approvals | CE, UL, cUL |
| Ambient Temperature | -10°C to +50°C |
| Storage Temperature | -40°C to +70°C |
| Relative Humidity | 5% to 95% (non-condensing) |
| Output Voltage | 0 V to Input Voltage |
Defines the skills and experience required for personnel to ensure safe operation.
Details crucial safety measures for installation, operation, and maintenance to prevent injury.
General safety warnings related to electrical installation, heat, wire types, and induced voltage.
Instructions for ensuring electromagnetic compatibility during electrical installation.
Details the wiring within the control compartment, including safety precautions and terminal connections.
Steps before applying power, including pre-start checks and critical safety warnings.
Overview of drive parameters, navigation through menus, and programming examples.
Procedures for testing motor rotation and encoder feedback before system start-up.
Step-by-step guide for the initial start-up of the drive after application setup is completed.
Lists and explains various warnings and alarms with their causes and troubleshooting steps.
Provides a table of symptoms, possible causes, tests, and solutions for common operational issues.
Detailed electrical specifications including output current, voltage, and cable sizes.
To Next Page