What to do for an inrush fault in Danfoss VLT AutomationDrive FC 302 DC Drives?
If your Danfoss DC Drives are showing an inrush fault, it means too many power-ups have occurred within a short time period. Let the unit cool to operating temperature.
What causes line power current imbalance greater than 3% in Danfoss DC Drives?
If you notice a line power current imbalance greater than 3% in your Danfoss DC Drives, it could be a problem with the line power supply itself. Check the line power supply. If the imbalance remains on the same input terminal, there may be a problem with the unit, and you should contact the supplier.
Why Danfoss VLT AutomationDrive FC 302 power on with red light?
If your Danfoss DC Drives show 'Power On' and the indicator is red, this typically indicates an IP Address Conflict. Resolve the IP conflict.
What to do if option configuration has changed in Danfoss VLT AutomationDrive FC 302 DC Drives?
If the option configuration has changed in Danfoss DC Drives, it means one or more options have either been added or removed since the last power-down. Check that the configuration change is intentional and reset the unit.
What to do if motor phase V is missing in Danfoss DC Drives?
If your Danfoss DC Drives report that motor phase V is missing, remove the power from the frequency converter and check motor phase V.
What to do if Danfoss VLT AutomationDrive FC 302 DC Drives show External error DI1?
If your Danfoss DC drive is showing 'External error DI1', it could be due to a safety input connected to DI1 having an illegal signal level, or the sensor might be broken. You can resolve this by checking that the configuration of DI1 (parameter 42-21 Type, sub-index [0]) is set correctly and that the connected sensor is installed according to specification. Additionally, you can extend the discrepancy time for DI1 using the VLT® Motion Control Tool MCT 10 Safe Plug-in.
What to do if Danfoss VLT AutomationDrive FC 302 show an earth fault?
If your Danfoss DC Drives indicates an earth fault, it means there's current leaking from the output phases to ground, either in the cable between the frequency converter and the motor, or within the motor itself. The solution is to remove power to the frequency converter and repair the earth fault.
What to do for option detection issues in Danfoss DC Drives?
If your Danfoss DC Drives detects a change in the option layout, enable option layout changes to apply the change.
How to troubleshoot motor thermistor overtemp in Danfoss VLT AutomationDrive FC 302?
If you are getting a motor thermistor overtemp warning on your Danfoss DC Drives, check whether the thermistor is disconnected. Also, check for motor overheating and if the motor is mechanically overloaded. When using terminal 53 or 54, ensure the thermistor is correctly connected between either terminal 53 or 54 (analog voltage input) and terminal 50 (+10 V supply), and that the terminal switch for 53 or 54 is set for voltage. If using terminal 18, 19, 31, 32, or 33 (digital inputs), ensure the thermistor is correctly connected between the digital input terminal used (digital input PNP only) and terminal 50.
What to do if Danfoss DC Drives show an over current error?
If you are experiencing an over current error with your Danfoss DC Drives, it might be due to shock loading or quick acceleration with high-inertia loads. First, remove the power and check if the motor shaft can be turned. Also, verify that the motor size matches the frequency converter and that the motor data is correctly set in parameters 1-20 to 1-25.
General| Category | DC Drives |
|---|---|
| Control Method | Flux Vector Control |
| Communication Options | CANopen, PROFIBUS |
| Cooling | Forced convection |
| Enclosure | IP20, IP21, IP55, IP66 |
| Protection Class/Rating | IP20 |
| Protection Features | Overvoltage, Undervoltage, Overcurrent, Overtemperature, Short Circuit |
| Approvals | CE, UL, cUL |
| Ambient Temperature | -10°C to +50°C |
| Storage Temperature | -40°C to +70°C |
| Relative Humidity | 5% to 95% (non-condensing) |
| Output Voltage | 0 V to Input Voltage |
Defines the skills and experience required for personnel to ensure safe operation.
Details crucial safety measures for installation, operation, and maintenance to prevent injury.
General safety warnings related to electrical installation, heat, wire types, and induced voltage.
Instructions for ensuring electromagnetic compatibility during electrical installation.
Details the wiring within the control compartment, including safety precautions and terminal connections.
Steps before applying power, including pre-start checks and critical safety warnings.
Overview of drive parameters, navigation through menus, and programming examples.
Procedures for testing motor rotation and encoder feedback before system start-up.
Step-by-step guide for the initial start-up of the drive after application setup is completed.
Lists and explains various warnings and alarms with their causes and troubleshooting steps.
Provides a table of symptoms, possible causes, tests, and solutions for common operational issues.
Detailed electrical specifications including output current, voltage, and cable sizes.
To Next Page