EasyManua.ls Logo

Danuser EP6 Hex - User Manual

Danuser EP6 Hex
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Owner:
Date Purchased:
Model #: Serial #:
Manual #:
Operator’s Manual
Danuser LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246 Fax: (573) 642-2240
E-mail: sales@danuser.com
Website: www.danuser.com
EP6 Hex,
EP10 Hex,
EP15 Hex,
EP20 Hex,
EP
HEAVY DUTY
AUGER SERIES
MODELS
EP6 Round
EP10 Round
EP15 Round
EP20 Round
Si no entiende ingles, se prefiere que
busque a alguien que interprete las
instrucciones para usted.
WARNING
Read this entire manual. This
safety alert symbol is used
throughout this manual to call your
attention to messages involving
your personal safety and the safety
of others. Failure to follow these
instructions can result in injury or
death.
9MEP2457351

Table of Contents

Questions and Answers

  • M
    Mary FisherAug 10, 2025
    Why is my Danuser Lawn and Garden Equipment oil overheating?
    • S
      Susan BrennanAug 10, 2025
      Oil overheating in your Danuser Lawn and Garden Equipment can occur due to several reasons: a low quantity of hydraulic oil, which can be solved by filling the reservoir to the proper level or increasing reservoir storage capacity; using improper oil, which requires replacement with the correct type; loose or damaged fittings and hoses, which necessitate tightening or replacement; and an improper hose size, which requires checking the hose diameter and length requirements.
  • P
    patricia88Aug 15, 2025
    What causes hydraulic hose failure in Danuser Lawn and Garden Equipment?
    • B
      Brittany KimAug 15, 2025
      Hydraulic hose failure in Danuser Lawn and Garden Equipment can be caused by: * Hydraulic relief pressure setting being too high, which requires adjusting the vehicle's hydraulic relief pressure setting to within the drive unit's specifications. * Hoses that are worn and damaged, which should be replaced. * A hose rating that is too low for the hydraulic system pressure, which means you should replace the hoses with ones that have a working pressure rated higher than the vehicle's hydraulic pressure. * Hoses that are pinched, which can be resolved by rerouting them.
  • H
    Holly JohnsonAug 19, 2025
    What to do if my Danuser Lawn and Garden Equipment has oil leaks?
    • R
      Ronald Ali IIIAug 20, 2025
      If your Danuser Lawn and Garden Equipment has oil leaks, check for loose or damaged fittings and tighten or replace them. Also, inspect hoses for looseness or damage, and tighten or replace as needed. If the hydraulic motor seals are worn or damaged, it is recommended to see your dealer for repairs.
  • M
    Monica ChavezAug 26, 2025
    Why is my Danuser Lawn and Garden Equipment slow?
    • A
      adkinsmichaelAug 26, 2025
      Slow speed in your Danuser Lawn and Garden Equipment could be due to fittings or connections that are too small or incompatible; replace them with proper fittings. It may also be caused by line restrictions, so clear the lines. Another potential cause is a worn or damaged hydraulic pump, in which case you should see your dealer for repairs.
  • J
    Jennifer WilsonAug 30, 2025
    Why does my Danuser Lawn and Garden Equipment lack drilling power?
    • M
      matazacharyAug 30, 2025
      If your Danuser Lawn and Garden Equipment lacks drilling power, it could be due to low system pressure (PSI). Check the pressure with a gauge, and if it's low, investigate the cause.
  • K
    kdawsonSep 4, 2025
    How to fix a Danuser Lawn and Garden Equipment auger that won't drill?
    • C
      Christopher MaddoxSep 4, 2025
      If your Danuser Lawn and Garden Equipment auger won't drill, it could be due to worn teeth or point, which should be replaced with new ones. Alternatively, the ground may be too hard and dry; in this case, order hardfaced or carbide teeth and a point.

Danuser EP6 Hex Specifications

General IconGeneral
ModelEP6 Hex
ManufacturerDanuser
Drive TypeHydraulic
Drive Adapter Compatibility2-inch hex
Auger Diameter6"
Auger Length48 inches
Output Shaft1-3/4 inch hex

Related product manuals