Danuser EP Series - User Manual

Questions and Answers

M
Michael LopezAug 13, 2025
Why is my Danuser EP hydraulic oil overheating?
- K
  Kristen HaydenAug 13, 2025
  Your Danuser Tools hydraulic oil might be overheating due to several reasons: the hydraulic oil quantity may be low, requiring you to add more hydraulic oil to the vehicle; the hydraulic oil may be improper, in which case you should replace it with the proper type; the hydraulic oil or filter may be dirty, so you should change the oil and filter according to the vehicle manufacturer's recommendation; or the hose size may be improper, requiring you to check the hose diameter and length requirements.
S
Sherry CraneAug 17, 2025
What to do if my Danuser EP Tools hydraulic hose fails?
- S
  Suzanne RobinsonAug 17, 2025
  If you experience hydraulic hose failure with your Danuser Tools, consider these potential causes and solutions: * The hydraulic relief pressure setting might be too high. Adjust the vehicle's hydraulic relief pressure setting to within the drive unit specifications. * The hoses might be worn or damaged, necessitating replacement. * The hose rating might be too low for the hydraulic system pressure. Replace the hoses with ones that have a working pressure rating higher than the vehicle's hydraulic pressure.
J
Jose WadeAug 20, 2025
Why is the auger speed slow on my Danuser EP Tools?
- P
  Pamela WatersAug 20, 2025
  A slow auger speed on your Danuser Tools could be due to several factors: low flow (GPM), which requires checking with a flow meter to investigate the cause; fittings or connections that are too small or incompatible, needing replacement with proper fittings; a pinched or kinked hydraulic hose, which needs fixing; dirty oil or filter, requiring a change according to the vehicle manufacturer's recommendation; or a worn or damaged hydraulic motor, in which case you should see your dealer for repairs.
A
Adrian MorganAug 25, 2025
What to do if my Danuser EP have gear oil leaks?
- K
  Keith RyanAug 25, 2025
  If your Danuser Tools are leaking gear oil, it could be due to a worn or damaged output seal, which would need replacement, or worn or damaged motor seals, causing hydraulic oil to leak into the gearbox, in which case you should see your dealer for repairs.
T
Tony DouglasAug 28, 2025
What to do if my Danuser Tools auger will not drill?
- B
  Brendan KeithAug 28, 2025
  If your Danuser Tools auger isn't drilling, it may be due to worn teeth or the point, suggesting you replace them. Alternatively, the ground may be too hard and dry, advising you to replace the dirt teeth and point with hardfaced or carbide teeth and point.
C
Chad GonzalezSep 1, 2025
Why does my Danuser Tools lack drilling power?
- C
  castanedaanthonySep 1, 2025
  Your Danuser Tools may lack drilling power due to low system pressure (PSI). Check with a pressure gauge, and if it's low, investigate the cause.
D
Dwayne CarneySep 4, 2025
What to do if my Danuser Tools have hydraulic oil leaks?
- A
  Alexa PruittSep 4, 2025
  If you notice hydraulic oil leaks in your Danuser Tools, the cause might be loose or damaged fittings (tighten or replace them), a loose or damaged hydraulic hose (tighten or replace it), or worn or damaged hydraulic motor seals, in which case you should see your dealer for repairs.
K
kwigginsSep 8, 2025
What to do if the drive unit is contacting the cradle on my Danuser EP?
- R
  Robert DaltonSep 8, 2025
  If the drive unit is contacting the cradle on your Danuser Tools, it is likely that the cradle is not installed in the proper position. Refer to Assembly & Installation to adjust carry angle.