32
LOCATIONS 368-371: LATE CLOSING/AUTO ARMING TIME
The Late Closing/Auto Arming Time is used to determine the Closing time, I.E. If a user Arms the DL250 after this time,
the Late to Close code will be reported is enabled. User code with authorisation restriction such as “Arm Only After Closing
Time” can not Disarm the DL250 After the Late Closing/Auto Arming Time. Late Closing/Auto Arming Time also marks the
time the Intelligent Auto Arming feature attempts to auto arm the DL250, if this feature is enabled in location 374.. To enable
the late closing report a 4 digit, 24 hour closing time must be entered in locations 368-371. For example, to enter a closing
time of 6:30 PM (1830), program a "1" in location 368, a "8" in location 369, a "3" in location 370 and an "0" in location 371.
Factory default is an "2-0-0-0" which sets a closing time of 8:00 P.M NOTE: A communicator code must be entered in
location(s) 348-351 if this feature is selected.
LOCATION 372: CLOSED SATURDAY ENABLE
A "1" should be programmed in location 372 if the DL250 will be closed on Saturdays and early opening or late to close
features have been enabled. A "1" will cause the early to open report to be communicated in the event an opening is made
on Saturday. User codes with authorisation restriction such as “Arm Only After Closing Time” can not Disarm the DL250
on a Saturday and auxiliary outputs following the open time will not activate if the feature is enabled. Factory default is "0"
and openings are allowed on Saturday within the assigned schedule without creating a report. Note: If auto-arm is enabled,
enabling closed Saturday will not allow the opening time to be valid all Saturday. This will result in the inability to disarm the
DL250 for more than 40 minutes at a time, as the auto-arm feature will attempt to arm the system during the closed time.
LOCATION 373: CLOSED SUNDAY ENABLE
A "1" should be programmed in location 373 if the DL250 will be closed on Sundays and early opening or late to close
features have been enabled. A "1" will cause a report to be communicated in the event of a late closing after an opening.
User codes with authorisation restriction such as “Arm Only After Closing Time” can not Disarm the DL250 on a Sunday and
auxiliary outputs following the open time will not activate if the feature is enabled. Factory default is "0" and openings are
allow on Sunday with the assigned schedule without creating a report. Note: If auto-arm is enabled, enabling closed Sunday
will not allow the opening time to be valid all Sunday. This will result in the inability to disarm the DL250 for more than 40
minutes at a time, as the auto-arm feature will attempt to arm the system during the closed time.
LOCATION 374: EARLY OPENING - LATE CLOSING / AUTO ARMING ENABLE
To enable the early opening/ late closing feature program a "1" into this location. A time must be programmed into locations
364-367 early open time and also locations 368-371 late close/autoarm time. To enable the auto arm feature program a
"2" into this location. A time must be programmed into locations 368-371. The automatic arming feature will be initiated
by the DL250 at the selected time. When all zones have been inactive for 5 minuted the buzzer will start beeping. One
minute later, if the buzzer is not silenced by the entry of a valid user code, the DL250 will autoarm. If the buzzer is silenced,
the DL250 will initiate a 40 minute delay. After the 40 minute delay, the DL250 will repeat the sequence of autoarming after
5 minutes of zone inactivity. The DL250 will only stop attempting to auto arm at the opening time programmed in locations
364-367. Default is “0" Early Opening - Late Closing / Auto Arming disabled.
VALUE EARLY OPENING \ AUTOARM ENABLE
0 ALL FEATURES DISABLED
1 EARLY OPENING \ LATE TO CLOSE REPORTING
2 AUTOARMING ENABLED
3 EARLY OPENING \ LATE TO CLOSE REPORTING
AUTOARMING ENABLED
LOCATION 375: AUTO CALLBACK ENABLE
This feature is used for the automatic download found in the “DASLOAD” download software. Programming a "1" in location
375 will cause the control panel to automatically call the download computer callback number at every autotest interval.
This feature will not activate unless a callback phone number has been programmed in locations 008-015, and a "2" is
programmed in location 024 in the DL250 download section.
LOCATION 376: RESERVED
To Next Page
Loading...