DAS DL-300E - Communicator Codes for Zones 22-30; Zones 22-25 Codes; Zones 26-30 Codes

34
Location 464-467: Programming the Communicator Code for
Zone 22
Locations 464-467 are used to control the communicator code for zone 22. Zone 22 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "22" when in alarm. Refer to appendix 1 ff a
different event type is required. The defaults are "3:2:2:5" with telephone number 1 and the event log enabled.
Location 468-471: Programming the Communicator Code for
Zone 23
Locations 468-471 are used to control the communicator code for zone 23. Zone 23 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "23" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:3:5" with telephone number 1 and the event log enabled.
Location 472-475: Programming the Communicator Code for
Zone 24
Locations 472-475 are used to control the communicator code for zone 24. Zone 24 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "24" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:4:5" with telephone number 1 and the event log enabled.
Location 476-479: Programming the Communicator Code for
Zone 25
Locations 476-479 are used to control the communicator code for zone 25. Zone 25 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "25" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:5:5" with telephone number 1 and the event log enabled.
Location 480-483: Programming the Communicator Code for
Zone 26
Locations 480-483 are used to control the communicator code for zone 26. Zone 26 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "26" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:6:5" with telephone number 1 and the event log enabled.
Location 484-487: Programming the Communicator Code for
Zone 27
Locations 484-487 are used to control the communicator code for zone 27. Zone 27 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "27" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:7:5" with telephone number 1 and the event log enabled.
Location 488-491: Programming the Communicator Code for Zone 28
Locations 488-491 are used to control the communicator code for zone 28. Zone 28 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "28" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:8:5" with telephone number 1 and the event log enabled.
Location 492-495: Programming the Communicator Code for Zone 29
Locations 492-495 are used to control the communicator code for zone 29. Zone 29 is automatically enabled and when
contact I.D is selected the default report is event "130 - Burglary" with point "29" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:2:9:5" with telephone number 1 and the event log enabled.
Location 496-499: Programming the Communicator Code for Zone 30
Locations 496-499 are used to control the communicator code for zone 30. Zone 30 is automatically enabled and when
contact ID is selected the default report is event "130 - Burglary" with point "30" when in alarm. Refer to appendix 1 if a
different event type is required. The defaults are "3:3:0:5" with telephone number 1 and the event log enabled.