Before programming the OL-300E for the first time, enter the "Go To Program Code" [9][7][f][3] from the code pad,
followed by the factory default function code [9][5][0][k]. The panel defaults will now match this installation manual and you
may begin programming the control panel. When using an optional plug-in programmer which automatically enters the
programming mode, the only entry necessary is [9][5][0][x] to load factory defaults.
ARM/DISARM CODES 1-15
LOCATION PAGE DESCRIPTION DATA 1 DATA 2 DATA 3 DATA 4 “DEFAULT”
000-003 9 USER #1 ARM/DISARM CODE (MASTER) “1-2-3-4”
004-007 9 USER # 2 ARM/DISARM CODE “15” DISABLED
008-011 9 USER # 3 ARM/DISARM CODE “15” DISABLED
012-015 9 USER # 4 ARM/DISARM CODE “15” DISABLED
016-019 8 USER # 5 ARM/DISARM CODE “15” DISABLED
020-023 8 USER # 6 ARM/DISARM CODE “15” DISABLED
024-027 8 USER # 7 ARM/DISARM CODE “15” DISABLED
028-031 8 USER # 8 ARM/DISARM CODE “15” DISABLED
032-035 8 USER # 9 ARM/DISARM CODE “15” DISABLED
036-039 8 USER # 10 ARM/DISARM CODE “15” DISABLED
040-043 8 USER # 11 ARM/DISARM CODE “15” DISABLED
044-047 8 USER # 12 ARM/DISARM CODE “15” DISABLED
048-051 8 USER # 13 ARM/DISARM CODE “15” DISABLED
052-055 8 USER # 14 ARM/DISARM CODE “15” DISABLED
056-059 8 USER # 15 ARM/DISARM CODE “15” DISABLED
060-063 8 GO TO PROGRAM ACCESS CODE “9-7-1-3”
ENABLING ARM/DISARM CODES 1-16 BY PARTITION (OPTIONAL)
LOCATION PAGE DESCRIPTION DATA "DEFAULT"
64 9 PARTITION(S) FOR USER # 1 ARM/DISARM CODE '15' ALL
65 9 PARTITION(S) FOR USER # 2 ARM/DISARM CODE CE' ALL
66 9 PARTITION(S) FOR USER # 3 ARM/DISARM CODE '15'ALL
67 9 PARTITION(S) FOR USER # 4 ARM/DISARM CODE '15' ALL
68 9 PARTITION(S) FOR USER # 5 ARM/DISARM CODE '15'ALL
69 9 PARTITION(S) FOR USER # 6 ARM/DISARM CODE '15' ALL
70 9 PARTITION(S) FOR USER # 7 ARM/DISARM CODE '15'ALL
71 9 PARTITION(S) FOR USER # 8 ARM/DISARM CODE '15'ALL
72 9 PARTITION(S) FOR USER # 9 ARM/DISARM CODE '15'ALL
73 9 PARTITION(S) FOR USER # 10 ARM/DISARM CODE '15'ALL
74 9 PARTITION(S) FOR USER # 11 ARM/DISARM CODE '15' ALL
75 9 PARTITION(S) FOR USER # 12 ARM/DISARM CODE '15'ALL
76 9 PARTITION(S) FOR USER # 13 ARM/DISARM CODE '15'ALL
77 9 PARTITION(S) FOR USER # 14 ARM/DISARM CODE '15'ALL
78 9 PARTITION(S) FOR USER # 15 ARM/DISARM CODE '15' ALL
79 PARTITION(S) FOR “GO TO PROGRAM” ACCESS CODE '15' ALL
PARTITIONED SYSTEMS NON PARTITIONED SYSTEMS
VALUE CHARACTERISTIC VALUE CHARACTERISTIC
1 Partition #1 1 Standard Arm/Disarm Code
2 Partition #2 2 Arm Only After Closing Time
4 Partition #3 4 Arm Only Code
8 Partition #4 8 Open/Close Reports For User
To Next Page
Loading...