Datalogic PowerScan D8300

To Next Page

To Previous Page

REFERENCES

169

Read only one code

to be associated with the special key sequence:

SHIFT

Ì12Î

CTRL

Ì23Î

ALT

Ì45Î

CTRL + SHIFT

Ì34Î

ALT + SHIFT

Ì56Î

CTRL + ALT

Ì67Î

Main Page

Table of Contents4
Introduction10
Installation11
Powerscan D8330 Interface Cable Connections11
BC-80X0 Interface Cable Connections13
Connection14
Usb14
Ibm Usb Pos15
WEDGE Connection16
PEN Emulation Connection16
Network Connections17
BC-8060 Network Connectors17
Network Cabling18
Network Termination19
Powerscan M8300 Battery Maintenance20
Battery Charging20
Replacing Powerscan M8300 Batteries20
2.10 Mounting the Bc-80X0 / C-8000 Cradle21
Desktop Mounting22
Wall Mounting25
Powerscan M8300 System and Network Layouts27
Stand-Alone Layouts27
Point-To-Point Reader Layout27
Stand-Alone Layout with Multiple Readers27
Multiple Stand-Alone Layouts28
C-BOX Layout29
Multidrop STAR-System™ Network Layouts30
Host Master Layout30
BC-8060 Master Layout31
Master BC-8060 Network Troubleshooting32
Configuration33
Configuration Methods33
Reading Configuration Barcodes33
Using Datalogic Aladdin33
Copy Command33
Sending Configuration Strings from Host34
Setup Procedures34
Powerscan ® D8330 Setup35
Powerscan M8300/BC-80X0 Point-To-Point Setup35
Using Multiple M-Series Readers with same Cradle38
Powerscan ® M8300/STAR-Modem™ in Stand-Alone Mode39
Powerscan M8300/Star-System™ Setup40
BC-8060 STAR-System™ Network Setup42
Interface Selection44
USB Reader Configuration47
Changing Default Settings49
Rs-232 Parameters50
USB Parameters55
Wedge Parameters61
Pen Emulation68
Network Parameters73
Data Format78
Power Save90
Reading Parameters92
Decoding Parameters98
Code Selection101
Advanced Formatting119
Radio Parameters138
Display and Keypad Parameters (3-Key Model)144
Display and Keypad Parameters (16-Key Model)148
References169
Parameters169
Handshaking169
ACK/NACK Protocol170
Fifo171
RX Timeout172
Pen Parameters172
Minimum Output Pulse172
Conversion to Code 39 and Code 128172
Overflow173
Output and Idle Levels173
Inter-Block Delay174
Network Parameters174
Slave Address Range First/Last174
Network Warning Message174
Reception Warning Message175
Master Header/Terminator Selection175
Data Format175
Header/Terminator Selection175
Define Special Key Sequence177
Address Stamping184
Address Delimiter184
Time Stamping Format185
Time Stamping Delimiter185
Power Save185
Sleep State185
Enter Sleep Timeout186
Reading Parameters186
Trigger Signal186
Trigger Click186
Trigger-Off Timeout186
Reads Per Cycle186
Safety Time187
Decoding Parameters187
Ink-Spread187
Overflow Control187
Interdigit Control188
Advanced Formatting188
Match Conditions188
Radio Parameters (M8300 Series Only)188
Radio Protocol Timeout188
Radio RX Timeout189
Power-Off Timeout189
Transmission Mode190
Beeper Control for Radio Response190
Single Store191
Batch Mode191
Find Me (Powerscan ® M8300 Only)193
Display Parameters (some M8300 Models Only)194
Display Mode194
5.11 Configuration Editing Commands195
5.12 Custom Default Configuration196
5.13 Code Type Recognition196
5.14 Configuration Copying Commands197
Copy Powerscan D8330 Series197
Copy Powerscan M8300 Series198
Copy BC-80X0199
5.15 Default Parameters for Pos Terminals200
5.16 Firmware Upgrade201
16-Key Powerscan M8300-DK Display and Keypad Parameters202
16-Key Keyboard Data Format Enable/Disable202
Scanner Code ID203
Scanner Code Length203
Message Formatting204
Standard Message Formatting204
16-Key DK Message Formatting205
Messages from Host to Reader207
Cursor Control208
Font Selection208
Clearing Display208
LED and Beeper Control209
Setting RTC209
Messages from SCANNER Command Keys210
Powerscan M8300 Keypad210
Powerscan M8300-DK 16-Key Keypad211
Technical Features212
Powerscan® D8330212
Powerscan M8300213
M8300-DK 16-Key Model214
Bc-80X0 / C-8000216
System and Radio Features217
Status Indicators217
Reading Tables220

Datalogic PowerScan D8300

Table of Contents

Related product manuals