Need help?Do you have a question about the Dell EqualLogic PS4210 and is the answer not in the manual?
General| Brand | Dell |
|---|---|
| Model | EqualLogic PS4210 |
| Category | Speaker System |
| Language | English |
Information intended for administrators responsible for installing array hardware.
Lists other Dell documents for FS Series appliances, PS Series arrays, groups, volumes, and software.
Information on Dell EqualLogic products and new releases.
Details on how to contact Dell EqualLogic Technical Support by phone and online.
Information on accessing Dell products and services online.
Details on PS4210 array warranty and registration.
Explanation of the symbols used in the manual to convey important information.
Overview of the Dell EqualLogic PS4210 storage array.
Lists the key hardware features and capabilities of the PS4210 array.
Lists the essential tools required for performing procedures in this section.
Guidelines for protecting the array hardware from electrostatic discharge.
Description of the front panel bezel and its role in physical security.
Step-by-step instructions for removing the front panel bezel.
Step-by-step instructions for installing the front panel bezel.
Details and descriptions of the front-panel components and status LEDs.
Details and descriptions of the back-panel components and status LEDs.
Procedure for safely powering down and restarting the array.
Information on supported drive types and compatibility.
Methods to identify a failed hard drive in the array.
Explanation of drive LED states for status indication.
How the array operates and responds when a drive fails.
Consequences of a drive failure when no spare is present.
Essential precautions for handling drives safely.
Rules and requirements for installing new drives.
Step-by-step procedure for removing a 2.5-inch drive.
Step-by-step procedure for installing a 2.5-inch drive.
Step-by-step procedure for removing a 3.5-inch drive.
Step-by-step procedure for installing a 3.5-inch drive.
Procedure for removing an empty drive slot cover.
Procedure for installing an empty drive slot cover.
Description of the features of the Type 19 control module.
Discussion of single vs. dual control module setups and redundancy.
Explanation of dual module setup and its benefits for redundancy.
Explanation of control module status LED indicators.
Methods to detect and diagnose control module failures.
Explanation of how failover mechanisms protect against module failure.
Procedures for updating and managing control module firmware.
Guidelines for safely handling and storing control modules.
Description of the standby on/off button on the control module.
Steps to enable the standby button feature groupwide.
Instructions on how to use the standby button to shut down the array.
Key points to consider when using the standby button.
Introduction to the process of replacing a control module.
Overview of procedures for replacing control modules.
Steps to replace the secondary control module in the array.
Steps to replace the active control module in the array.
Steps to replace both control modules in the array.
Step-by-step procedure for removing a control module from the array.
Step-by-step procedure for installing a control module into the array.
Overview of replacing the microSD card in a control module.
Detailed steps for replacing the microSD card.
Procedure for safely removing the microSD card.
Procedure for safely inserting the microSD card.
Steps for replacing the battery in a PS Series array control module.
Guidelines for safely discharging and shipping the array.
Preparatory steps before removing the battery.
Step-by-step procedure for removing the battery from the control module.
Steps to install a new battery into the control module.
Information on proper disposal or return of old batteries.
Overview of optional advanced network configurations.
Steps for configuring the management port for dedicated traffic.
Software configuration steps for the management network.
Information about the power supply units used in the array.
Methods to identify failures in power supply and cooling modules.
Explanation of power supply LED indicators for status.
Procedure for removing a power supply and cooling module.
Procedure for installing a power supply and cooling module.
General safety precautions to follow during troubleshooting.
How to locate and provide the array's service tag.
Methods for collecting diagnostic information from array components.
Checks to perform if the system fails to start up correctly.
Troubleshooting steps for issues with array internal connections.
Troubleshooting steps for external cable and connectivity issues.
Steps to diagnose and resolve power supply failures.
Checks for and solutions to array cooling system issues.
Steps to diagnose and resolve control module failures.
Steps to diagnose and resolve issues with faulty hard drives.
To Next Page
