To Next PageTo Next PageWhat to do if my Denon AVR-1802/882 isn't responding to the remote control?
If your Denon Receiver isn't responding to the remote, try these solutions: * Replace the batteries with new ones. * Move closer to the receiver. * Remove any obstacles between the remote and the receiver. * Make sure you're pressing the correct button. * Ensure the batteries are inserted correctly, with the < and > ends properly aligned.
Why is there no sound from my Denon Receiver, even though the display is on?
There are several reasons why your Denon Receiver might have a lit display but no sound. Check these possible causes: * Ensure speaker cords are securely connected. * Verify the audio function button is in the correct position. * Increase the volume, as it might be set to the minimum. * Deactivate MUTING if it's enabled. * If using digital input, ensure digital signals are being input or that the correct input jacks are selected.
Why is my Denon AVR-1802/882 not turning on - no display and no sound?
If your Denon Receiver's display isn't lit and there's no sound when the power switch is on, the power cord may not be securely plugged in. Check the power cord to ensure it's properly inserted. Also, after turning the POWER operation switch on, turn the power off with the remote control unit.
How to fix a Denon AVR-1802/882 Receiver when the display is off and the ON/STANDBY LED is flashing rapidly?
If the display of your Denon Receiver is not showing anything and the “ON/STANDBY” LED is flashing quickly, it could be due to a few reasons: * A short circuit in the speaker terminals. In this case, switch the power off, properly connect the speakers, and then switch the power back on. * Blocked ventilation holes. Turn off the receiver, allow it to cool down with proper ventilation, and then turn it back on. * Continuous operation at high power with inadequate ventilation. Turn off the receiver, ensure it has good ventilation to cool down, and then turn it back on.
Why is sound only coming from one channel on my Denon Receiver?
If sound is only coming from one channel on your Denon Receiver, it might be due to incomplete connections. Ensure that both the speaker cords and the input/output cords are securely connected.
General| Total Harmonic Distortion (THD) | 0.08% |
|---|---|
| Tuner Frequency Range | FM: 87.5 - 108 MHz, AM: 522 - 1611 kHz |
| Power Output per Channel | 80 Watts into 8 Ohms (20 Hz - 20 kHz, 0.08% THD) |
| Frequency Response | 10Hz - 100kHz |
| Input Sensitivity | 200mV |
| Input Impedance | 47k ohms |
| Surround Sound Formats | Dolby Digital, DTS |
| Digital Inputs | 2 optical, 1 coaxial |
| Analog Inputs | 5 |
| Video Inputs | 3 |
| Video Outputs | 1 |
| Digital Outputs | 1 optical |
Warning to reduce electric shock risk by not removing the cover.
Instructions for safe plug insertion to prevent electric shock.
General advice on handling and operating the unit safely.
List of included accessories with the AV receiver.
Initial steps and considerations before operating the unit for the first time.
Identification and function of front panel controls and indicators.
Details the buttons and operation of the remote control unit.
Optimal distance and conditions for remote control use.
Guide on how to insert batteries into the remote control.
How to control DENON and other components using the remote's preset memory.
Diagram showing a typical speaker system configuration for home theater.
Guide to connecting turntables, tape decks, and pre-out jacks.
Instructions for connecting video sources like CD players, cameras, and game consoles.
How to connect tuners, DVD/VDP players, and VCRs.
Details on connecting devices using S-Video for enhanced video quality.
Instructions for connecting FM and AM antennas for radio reception.
How to connect speakers, including polarity and banana plug usage.
Overview of configurable settings and their factory default states.
Preliminary steps before starting system configuration.
How to configure speaker types and sizes for surround sound.
How to configure subwoofer settings for bass playback.
Adjusting speaker delay times for optimal audio timing.
Configuring digital audio input sources.
Final steps to complete the system setup.
Preparatory steps before initial operation.
How to turn the unit on/off and select front speakers.
Explanation of different input modes (AUTO, PCM, DTS, ANALOG, EXT. IN).
Specific guidance for playing DTS encoded content.
How to choose different surround sound modes.
How to adjust bass, treble, and tone defeat.
Using headphones and temporarily muting audio output.
How to achieve simulcast playback and check unit status.
How to use external audio/video inputs directly.
Instructions for recording audio/video signals.
Preparatory steps for surround sound setup.
How to adjust individual speaker volume levels.
Overview of available DSP surround modes and their characteristics.
Adjusting the perceived room acoustics for surround sound.
Adjusting the intensity of the surround effect.
Automatically scans and stores FM stations.
Steps for automatic radio station tuning.
Steps for manually tuning radio stations.
How to save tuned radio stations.
How to select stored radio stations.
Unit remembers last used settings before power off.
Procedure to reset the unit to factory defaults.
Guidance on optimal speaker placement for different purposes.
General explanation of the unit's surround sound capabilities.
