Why is the power indicator blinking red after turning on my Denon Av receiver?
If, after turning on the power, the power indicator is blinking red in intervals of approximately 0.5 seconds on your Denon Av receiver, this indicates that the unit's amplifier circuit has failed. Turn off the power and please contact the DENON service adviser.
How to fix Denon Av receiver when it does not operate properly?
If your Denon Av receiver isn't operating properly, try resetting the microprocessor.
Why is there no sound coming from the subwoofer of my Denon Av receiver?
If you're not getting sound from your subwoofer with your Denon Av receiver, verify the subwoofer connections and ensure the subwoofer is powered on. On the receiver's menu, set “Speaker Config.” – “Subwoofer” to “Yes”. Note that if “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected sound mode.
What does it mean when the power indicator is blinking red on my Denon Av receiver?
If the power indicator on your Denon Av receiver is blinking red in intervals of approximately 0.5 seconds, it could indicate that you are not using speakers with the specified impedance or the protection circuit has been activated. This can happen if the speaker cable core wires are touching, a core wire has come loose from the terminal, or a core wire is touching the rear panel of the unit. To resolve this, unplug the power cord, correct any wiring issues by re-twisting the core wire or securing the terminal, and then reconnect the wire.
How to fix no video output with HDMI connection on Denon Av receiver?
If you're experiencing no video output via HDMI on your Denon Av receiver, start by checking the HDMI connector's connection. Make sure the input source matches the connected HDMI connector. Also, verify that your TV is compatible with copyright protection (HDCP); incompatible devices may prevent correct video output.
What to do if Denon Av receiver power automatically switches to standby mode?
If your Denon Av receiver is automatically switching to standby mode, it could be due to the sleep timer being set. Turn the power back on or adjust the sleep timer settings. Alternatively, the “Auto Standby” feature might be enabled, which activates after a period of inactivity. To disable this, set “Auto Standby” on the menu to “Off.”
Why is there no audio output with HDMI connection on my Denon Av receiver?
If you're not getting any audio output via HDMI on your Denon Av receiver, first check the HDMI connector's connection. Then, depending on where you want the audio to output, check the following: * To output audio from the speakers, set “HDMI Audio Out” on the menu to “AVR”. * To output audio from a TV, set “HDMI Audio Out” on the menu to “TV.”
General| Channels | 7.1 |
|---|---|
| HDMI Inputs | 6 |
| HDMI Outputs | 1 |
| Network Capability | Yes |
| HDMI Pass-Through | Yes |
| Audio D/A Converter | 192kHz/24-bit |
| Input Impedance | 47 kOhms |
| Input Sensitivity | 200 mV |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 100 dB |
| HDMI Switching | Yes |
| 3D Technology | Yes |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.08 % |
| Bluetooth | No |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Streaming Services | AirPlay, Pandora |
| Dimensions (W x H x D) | 17.1 in x 6.6 in x 13 in |
| Surround Sound Effects | DTS Neo:6, Dolby Pro Logic IIz |
| Additional Features | Audyssey Dynamic EQ, Audyssey Dynamic Volume, Audyssey MultEQ XT |
| Inputs | HDMI input |
| Outputs | HDMI output |
| Video Upconversion | Yes |
| Power Output (8 ohms) | 95 W |
Essential safety guidelines for operating the audio-visual receiver.
Regulatory compliance details for users in the United States.
Cautionary notice regarding hot surfaces during operation.
Important warnings and guidelines for safe unit handling and use.
Recommendations for unit placement to ensure proper heat dissipation.
Introduction to basic functions and operations of the unit.
Guides for connecting compatible and incompatible devices.
Steps for initial setup, including speakers and network.
Instructions for fundamental playback functions.
Detailed steps for speaker installation, connection, and configuration.
In-depth guides for advanced playback features and functions.
Instructions for playing audio in a separate room (ZONE2).
Comprehensive guide to configuring various unit settings via the menu.
Adjusting surround audio effects for personalized listening.
Settings for tone control, dialogue, subwoofer, and volume.
Configuration of Audyssey MultEQ XT, Dynamic EQ, and Dynamic Volume.
Adjustments for dynamic sound quality and frequency equalization.
Settings for contrast, brightness, saturation, hue, noise, and enhancer.
Configuring HDMI output, audio, and control functions.
Managing video output, conversion, and scaling settings.
Setting video output resolution and aspect ratio for displays.
Assigning, renaming, hiding, and selecting input sources.
Adjusting input source levels and selecting video sources.
Connecting to and configuring network settings for LAN.
Manually configuring speaker assignments and configurations.
Setting speaker volume levels and crossover frequencies.
Configuring front speaker usage for different playback modes.
Customizing language, zone, standby, and display settings.
Managing firmware updates and notification settings.
Protecting settings from accidental changes.
Identification of unit components and their functions.
Guidance for resolving common problems and symptoms.
Detailed technical specifications of the audio-visual receiver.
Explanation of each button's operation on the remote control.
Instructions for inserting batteries and remote operating range.
Table showing sound modes, speaker outputs, and adjustable parameters.
Chart mapping input signals to corresponding sound modes.
To Next Page
