Denon AVR-3200

Remote
control
unit learning function
This unit’s
remote
control
unit
If
your
AV
components
are not DENON
products
or if operation
is
not possible
with
the
preset
memory
settings,
the
components’
remote control
signals
can be “learned” to
enable
remote control operation.
The buttons
that can
be
“learned” are
the
CD,
DAT and DECK system buttons
lsee
page
191
and
the VDP,
VCR and
TV
system buttons
(see
page
211. (For
the
TV
only,
the A block buttons
can also
be
“learned”
.1
1
Press
the USE/LEARN
selector
button
with the tip
of
a
pen
etc.,
to
set
the
learn mode.
Both the START
and
LEARNED/TX
indica
tors
flash.
Flashes
i:
:°
D3I
BöJ
A—
2
Set
the program
switch to the
side to be “learned”.
Set to the
AUDIO side
for the CD,
tape
deck or DAT
position,
to
the
VIDEO side
for the VDP,
VCR or TV position.
AUDIO
AVR/AVC VIDEO
3
Set
the program switch
to the
position to
be
“learned”
cD DECK DAT
VDPVCR
TV
5
Check
that the
START
LED
is lit, then press
the
button to be
“learned”
on the
other
remote
control unit.
(c(3cc
-_c
Transmitting’
6
Once the START
LED turns
off
and
the
LEARNED/TX
LED lights,
release
the
button
on the
other
remote control
unit.
Lit
E
remote
control
unit
Approx.
5cm
This unit’s
remote
control
unit
4
Set
the
remote
control units
so
they are facing
each
other, then
press the button
to be “learned”
on
this unit’s remote control
unit.
The
indicator
stops
flashing and
the START LED lights.
The learnable
buttons
are the buttons
which
can be
operated
with
the DENON
system
codes
for the CD player,
DAT and
tape
deck, the
buttons
which can
be
operated
with the
preset
memory for
the
VCR, VDP and
TV. For the TV
only,
however,
the
buttons in
the section indicated
“A” on
the diagram above can
also
be “learned”
. Use these to
“learn”
TV channels.
NOTE: Use button
®
I
0 as
the 0 number button,
button
©
I
E
as
the enter
button.
The two LEDs
start flashing
again.
7
To “learn”
other buttons,
repeat steps
2
to 6.
8
Once
the
learning
operation
is
completed,
press the
USE!
LEARN
selector button
again.
The
two
LEDs
stop flashing
and the learning
mode is cancelled.
I
Check
that the stored
codes
work properly.
NOTES:
.
Up
to
26 codes can
be “learned” ,
but
this
number
may
be lower
if the codes
are
long.
.
If a non—learnable
button
is
pressed or two
or
more buttons
are pressed at
once,
the
two
LEDs will once
again light
when the
button(s)
is
released.
.
If the
codes could not
be stored, the
LEARNED/TX
LED does
not
light after
the START
LED
turns
off. For
limited
number
of models, codes
cannot
be
stored
in RC—825.
.
If the two
LEDs start
flashing
rapidly
after
the START
LED
lights, this
means
that the
memory
is already
full,
and the code
you
have just
attempted
to store
was
not
stored.
To “learn”
that
code,
first
perform the resetting operation.
22