Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting SpecificationsPlayback
Check the HD Radio Reception
Information
Press <STATUS> while an HD Radio broadcast is being
received.
The current reception information is shown on the display.
q Normal
↓
w Frequency / Signal strength
↓
e Long station name / Program and Program type
↓
r Title name / Artist name
↓
t Album name / Genre name
NOTE
If the station signal weakens while receiving a digital broadcast (while
“ ” and text is displayed), the mode automatically switches to the
analog reception mode (the reception frequency is displayed).
Because of this, the “ ” indicator and text may flicker if the station
signal level is weak and unstable.
n Default settings
Tuner presets
A1 ~ A8 87.5 / 87.9 / 89.1 / 93.3 / 97.9 / 98.1 / 98.9 /100.1 MHz
B1 ~ B8
101.9 / 102.7 / 107.9 / 90.1 / 90.1 / 90.1 / 90.1 / 90.1
MHz
C1 ~ C8 530 / 600 / 930 / 1000 / 1120 / 1210 / 1400 / 1710 kHz
D1 ~ D8 90.1 MHz
E1 ~ E8 90.1 MHz
F1 ~ F8 90.1 MHz
G1 ~ G8 90.1 MHz
Selecting Audio Programs
HD Radio includes up to 9 audio programs (HD1 to HD8
and Analog). The different audio programs also have data
programs.
Press [SEARCH] or ui to select the audio program.
If the station you are listening to has multiple audio programs, “HD1”
is indicated on the display. If it only has one audio program, “HD” is
indicated.
If an audio program from HD2 to HD8 has been interrupted or if a program
is called out using the preset buttons after it has been interrupted, HD1 is
automatically selected after about 20 seconds.
About the button names in these explanations
< > : Buttons on the main unit
[ ] : Buttons on the remote control unit
Button name only:
Buttons on the main unit and remote control unit
<SOURCE SELECT> <STATUS>
ENTER<ON/STANDBY>
uiop
[REPEAT]
[8]
[2]
[RAMDOM]
[9]
[1/3]
(Main remote control unit)
(Sub remote control unit)
uiop
[SEARCH]
[
NET/DTU]
(DEVICE2 mode)
uiop
[SEARCH]
[POWER OFF]
[ iPod]
[iPod]
(AMP mode)
[CHANNEL
+/–
]
ENTER
[8],[9],
[6],[7],
[1],[2]
iPod
®
Playback
The music on an iPod can be played by using the Control
Dock for iPod (ASD-1R, sold separately).
The operation can also be performed using the buttons on
the main unit or remote control unit while watching the GUI
menus.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
1
Make the necessary preparations.
q Set the iPod in the DENON Control Dock for iPod.
(vSee the Control Dock for iPod’s operating instructions.)
w Assign the Control Dock for iPod’s input.
: ”Source Select” – “(input source)” – “Assign”–
”iPod dock” (vpage 42)
2
Either turn <SOURCE SELECT> or press [iPod] (AMP
mode) to select the input source assigned in step 1-w
above.
(iPod screen)
b If the screens above are not displayed, the iPod may not be
properly connected. Try connecting again.
: ”Source Select” – “(input source)” – “Play”
(
vpage 40)
3
To operate using the main remote control unit, set the
remote control unit to the iPod mode.
(vpage 64 “Remote Control Unit Operations”)
OK to disconnect
Basic Operation