O
Olivia FarmerSep 10, 2025
What to do if Denon AVR-589 Stereo Receiver display is off?
- DDalton LopezSep 10, 2025
If the display is off, the Dimmer setting is set to “OFF”. Set to something other than “OFF}.
To Next PageTo Next PageWhat to do if Denon AVR-589 Stereo Receiver display is off?
If the display is off, the Dimmer setting is set to “OFF”. Set to something other than “OFF}.
What to do if my iPod cannot be played on Denon AVR-589 Stereo Receiver?
If your iPod cannot be played, switch to the input source assigned at control dock for iPod. Reconnect the cable. Ensure the control dock for iPod’s AC adapter is plugged into a power outlet.
Why does Denon Stereo Receiver display flash red?
If the Denon Stereo Receiver power display flashes red, switch off the power and contact the DENON service advisor, as the amplifier circuit may have failed.
What to do if no sound is produced from speakers on Denon AVR-589?
If no sound comes from the speakers, check the connections with input devices and speaker cables. Ensure the device you want to play matches the set input source. Adjust the master volume, and make sure mute mode is off. Disconnect headphones if connected. Verify digital signals are being input, and that connectors and settable input modes match.
What to do if Denon AVR-589 does not operate properly?
If the Denon Stereo Receiver is not operating properly, reset the microprocessor.
Why does my Denon AVR-589 Stereo Receiver keep turning off?
The Denon Stereo Receiver may be turning off due to the protection circuit being activated by a temperature rise in the unit's internal parts. Immediately switch off the power, and re-apply it after the body temperature has sufficiently cooled. Re-install the unit in a location with good ventilation.
What to do if Denon Stereo Receiver remote control not working?
If the remote control isn't working, replace the batteries with new ones and ensure you are operating within the specified range without obstacles. Check the batteries are inserted correctly, and the unit isn't exposed to strong light. Verify the remote ID is set to “1” and the SOURCE CONTROL switches are in the correct positions.
Why does Denon AVR-589 Stereo Receiver power switch off suddenly?
The Denon Stereo Receiver may suddenly switch off if speakers have impedance lower than specified, or if speaker cable core wires touch each other or the AVR-589 rear panel. To resolve this, use speakers with the specified impedance. Unplug the power cord, twist the core wires together tightly or effect termination treatments, and then reconnect.
What to do if no picture appears with HDMI connections on Denon Stereo Receiver?
If there is no picture when using HDMI connections, check the HDMI connector connections and the HDMI input setting. Also, ensure that the HDMI format of the player and monitor are compatible.
How to fix no DTS sound output on Denon AVR-589 Stereo Receiver?
If DTS sound is not being output, set the DVD player’s audio output setting to bitstream. Use a DTS-compatible player. Set the AVR-589’s “Input Mode” setting to “Auto” or “DTS” mode.
General| Input Sensitivity | 200 mV |
|---|---|
| HDMI Switching | Yes |
| Frequency Response | 10Hz-100kHz |
| Inputs | 4 x composite |
| Outputs | 1 x HDMI |
| Input Impedance | 47 kΩ |
| Tuner Type | Digital |
| Tuner Bands | AM/FM |
| Audio D/A Converter | 192 kHz/24-bit |
| Tuner Frequency Range | FM: 87.5 - 108 MHz |
| Dimensions (W x H x D) | 434 x 171 x 377 mm |
Crucial safety check before returning unit to customer to ensure protection.
Cautions for servicing, electric shock, disassembly, parts usage, and wiring.
Explanation of parts marked with 'z' that have critical safety characteristics.
Outlines the sequence for dismantling and reassembling components correctly.
Shows the disassembly steps with corresponding image references for clarity.
Describes the procedure for initializing the AV receiver or amplifier after component replacement.
Lists required jigs and tools for board repair and firmware updates.
Describes how to enter and use the error history display mode.
Explains how protection history is displayed on the FL display.
Details methods for clearing the protection history.
Details the steps to adjust the idling current using test points and controls.
Provides a flowchart to diagnose power-on problems.
Guides through troubleshooting steps for a blown fuse.
Details checks for video output issues on the AVR-1709 model.
Details checks for video output issues on the AVR-1609 model.
Provides a flowchart for diagnosing HDMI/DVI output issues.
Shows the main unit's schematic diagram.
Shows schematics for input, CPU, and front units.
Shows schematics for HDMI, Sirius, and video units.
Shows schematics for power and 2CH amplifier units.
