Denon AVR-990 User Manual


Getting Started Connections Remote ControlZONE2 Information Troubleshooting Specifications
ENGLISH
Making the Input Settings (Input Setup)
Setting contents
–12dB ~ +12dB (0dB)
The analog input level and digital input level can be adjusted independently for input sources for
which “HDMI” or “Digital” is assigned at “Input Assign“ (vpage 45).
Corrects the playback level of the selected input source’s audio input.
Set this if there are differences in the input volume levels between the different sources.
•
•
Correcting the Input Source’s Playback Level
(Source Level)
Default settings are underlined.
Setting items Setting contents
Rename
Change the display name of
the selected input source.
1. Press p or ENTER.
2. Use o p to set the cursor to the character you want to change.
3. Use ui to change the character, then press ENTER.
Up to 8 characters can be input.
The input character type can be switched by pressing [SEARCH] while
the display name is being changed.
The types of characters that can be input are as shown below.
•
•
•
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! “ # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜
(Space)
GNumbersH 0123456789
4. Repeat steps 2 and 3 to change the display name.
Default
Reset all settings to factory
default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
If you select “Default” and press ENTER the message “Default
Setting?” is displayed. Select “Yes” or “No”, and then press ENTER.
Changing the Input Source’s Display Name (Rename)
Setting items Setting contents
Input Mode
Set the audio input modes for
the different input sources.
Auto : Automatically detect input signal and perform playback.
HDMI : Play only signals from HDMI input.
Digital : Play only signals from digital input.
Analog : Play only signals from analog input.
EXT. IN : Play only signals from EXT. IN input.
“HDMI” can be set for input sources for which “HDMI” is assigned at
“Input Assign”.
“Digital” can be set for input sources for which “Digital” is assigned at
“Input Assign”.
When digital signals are properly input, the ” ” indicator lights on
the display. If the ” ” indicator does not light, check the digital input
connector assignment and the connections.
The surround mode cannot be set if the input mode is set to “EXT. IN”.
This can also be set by pressing [INPUT MODE]. Each time you press the
button, the input mode display will change.
•
•
•
•
•
Auto HDMI Digital
AnalogEXT. IN
Decode Mode
Set the decode mode for
input source.
This can be set when the input source is
CD DVD HDP TV
SAT/CBL VCR DVR V.AUX
.
Auto : Detect type of digital input signal and decode and play
automatically.
PCM : Decode and play only PCM input signals.
DTS : Decode and play only DTS input signals.
This can be set for input sources for which “HDMI” or “Digital” is
assigned at “Input Assign” (vpage 45).
Normally set this to “Auto”. Set “PCM” and “DTS” when inputting the
corresponding input signal.
•
•
The selectable input modes depend on the input source and “Input Assign” (vpage 44) setting.
Changing the Input Mode and Decoding Mode
(Input Mode)
Default settings are underlined.
Remote control operation
buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
PlaybackSettings

Denon AVR-990 Specifications

General

Brand	Denon
Model	AVR-990
Category	Stereo Receiver
Language	English