Denon DCD-695 - Page 10

ENGLISH
(2) Checking the Programmed Tracks
(Remote control only)
{ CALL )
=e
e Press the CALL button.
The programmed tracks are displayed in order on the TRACK
NO. display each time the CALL button is pressed.
(3) Playing the Programmed Tracks
( » PLAY )
© Press the ( » PLAY) button to play the tracks in the program-
med order.
(4) Clearing the Program
@ The entire program is cleared when the PROG/DIRECT button
is pressed again. The program is also cleared when the ( &
OPEN/CLOSE) button is pressed.
e If the PROG/DIRECT button is pressed during programmed
play, the program is cleared and playback continues normally
through to the last track on the disc.
NOTES
e If programming is done in the play or pause mode, the
track currently playing is programmed at the first
position. Other tracks can be added to the program, but
the number of programmed tracks and the playing time
will not be displayed.
e Direct search is not possible during programmed play. If
the number buttons are pressed, that track is added to
the end of the program.
e@ Programming is possible with the disc holder open.
Track numbers greater than the number of tracks
recorded on the disc can be programmed, but will be
automatically cleared before playback begins.
@ The remaining time per track will only be displayed for
track numbers 1 through 20.
© The total program time and remaining program time are
not displayed if tracks greater than track number 20 are
programmed.
6 Repeating playback ...............esssssserescesescrrseesesseeees
(Remote control only)
( D> PLAY )
@ Press the repeat button (ALL).
@ Press the play button ( » PLAY).
¢ Pressing the repeat all tracks button (ALL), is
displayed.
® Steps @ and @ above may be reversed.
¢ To cancel repeat playback of all tracks, press the repeat button
(ALL) once more.
¢ Pressing the repeat button (ALL) during programmed play-
back, playback of the tracks entered into the memory will be
repeated.
10
( t! PAUSE)
e@ Playback can be temporarily halted and then continued from
the same point in the track.
. Press the pause button (lf PAUSE) during playback.
. To continue playback, press the play button ( » PLAY) or the
pause button (1 PAUSE) once more.
(7) Audible quick search .............ccccccsssscssseeseees Manual Search
e Using this function, you can cue to a desired point within a
track, either in the forward or reverse direction.
e Release the manual search button ( €@ or PP ) when the
desired point has been reached. Normal playback then
continues.
NR —
(1) Manual Search Forward
1. Press the manual search forward button ( PP ) during play-
back. Playback of the track is sped up.
e Asa reference, the current track number and elapsed playback
time within the track are displayed.
e@ Manual search forward is approximately three times faster
when engaged during the pause state compared to playback.
In this case, no sound is heard however.
e If the manual search forward button ( PP ) is kept pressed
after the end of the final track on the disc is reached, ( 37) is
displayed and manual search stops. To return to another
point, press the manual search reverse button ( €@ ) until
(33) disappears.
(2) Manual Search in Reverse
1, Press the manual search reverse button ( ¢@ ) during play-
back. Reverse playback of the track is sped up.
e Asa reference, the current track number and elapsed playback
time within the track are displayed.
® Manual search in reverse is approximately three times faster
when engaged during the pause state compared to playback.
In this case, no sound is heard however.
e Ifthe manual search reverse-button ( ¢€ ) is kept pressed after
the
beginning
of
the
first
track
on
the
disc
is
reached,
(
CL)
is
displayed and manual search stops. To return to another
point,
press
the
manual
search
forward
button
(
PP
)
until
(CC) disappears.