Why is there no sound from my Denon DRA-697CI?
If your Denon Stereo Receiver display is lit but no sound is produced, consider these potential causes: * Ensure the speaker cables are securely connected. * Verify the FUNCTION knob is set to the appropriate position. * Check that the volume control is not set to the minimum level; turn it up. * Make sure MUTING is switched off.
What to do if my Denon Stereo Receiver display is not lit and there is no sound?
If the display isn't lit and no sound is coming from your Denon Stereo Receiver when the power switch is on, check that the power supply cord is securely plugged in.
Why is there no sound from the subwoofer connected to my Denon Stereo Receiver?
If you're not getting any sound from the subwoofer connected to your Denon Stereo Receiver, check the following: * Ensure the subwoofer's power is turned on. * Verify the subwoofer's output is properly connected. * Check that the subwoofer's channel volume level isn't set too low (e.g., “–12 dB”); turn it up.
Why is my Denon DRA-697CI Stereo Receiver remote control not working?
If your Denon Stereo Receiver isn't responding to the remote, here's what you can check: * Make sure the batteries aren't dead by replacing them with new ones. * Ensure you're close enough to the unit. * Remove any obstacles blocking the remote's signal. * Verify you're pressing the correct button. * Check that the batteries are inserted with the correct polarity.
What to do if my Denon DRA-697CI power is off and the power indicator is blinking red?
If the power indicator on your Denon Stereo Receiver is blinking red and the power is off, it indicates the protection circuit has been activated. This could be due to a few reasons: * The unit's internal temperature may have risen. Ensure the receiver is in a well-ventilated area. * The speaker wires might be touching each other or the receiver's rear panel. Check all speaker cable connections. * Turn off the power and allow the unit to cool down fully before turning it back on.
Why does my Denon DRA-697CI show 'CHECK ANTENNA' in XM mode?
If your Denon Stereo Receiver displays 'CHECK ANTENNA' in XM mode, it means the XM connectors and the XM Mini-Tuner and Home Dock are not properly connected. Double-check that these connections are correct.
Why does my Denon DRA-697CI show 'NO SIGNAL' in XM mode?
If your Denon Stereo Receiver displays 'NO SIGNAL' in XM mode, it indicates that the signal cannot be received. Try repositioning your XM Mini-Tuner and Home Dock.
What to do if nothing is displayed on the monitor connected to my Denon DRA-697CI Stereo Receiver?
If nothing is displayed on the monitor connected to your Denon Stereo Receiver, verify the following: * The receiver's video output terminals and the monitor's input terminals are correctly connected. * The monitor's input selector is set to the terminals to which the video signals are connected.
Why does my Denon DRA-697CI show 'OFF AIR' in XM mode?
If your Denon Stereo Receiver displays 'OFF AIR' in XM mode, it means the selected channel is not currently broadcasting. Try selecting another channel.
Why am I receiving only XM channels 0 and 1 on my Denon DRA-697CI Stereo Receiver?
If you're only receiving XM channels 0 and 1 on your Denon Stereo Receiver, it suggests that the XM Tuner is not activated. You should contact XM Radio to resolve this.
Covers essential safety precautions for operating the appliance.
Details FCC compliance, modification notices, and interference handling.
Advice on handling, environment, and maintenance for proper operation.
Lists accessories, initial setup, and remote control overview.
Notes on battery management, safety, and operating range for remote controls.
Identifies front panel controls and explains display indicators.
Details rear panel terminals and RC-1052 remote functions.
Guidelines for cables, speaker connection, and impedance.
In-depth speaker connection guide and video device wiring.
Instructions for connecting TV/DBS, CD players, turntables, decks, and VCRs.
Guides for connecting antennas and the XM Ready receiver.
Instructions for connecting iPods and setting up multi-zone audio.
Connecting trigger outputs, RS-232C, audio terminals, and power cord.
Assigns iPod and configures trigger out functions.
Adjusts the high pass filter for speaker bass response.
Steps for powering on, muting, headphone use, and speaker selection.
Adjusting tone, volume, display, PURE DIRECT, and video source.
Tuning FM/AM stations, auto preset, manual tuning, and recall.
Overview of XM service, features, and subscription details.
Checking signal, direct access, and category search for XM channels.
Connecting and playing music from an iPod.
Browsing music, viewing photos/videos, and safely disconnecting iPod.
Explanation of multi-zone system and PREOUT connections.
Outputting sources to zones and using remote controls for multi-zone playback.
Recording audio/video, memory functions, and microprocessor reset.
Controlling devices, setting presets, and punch through function.
Mapping front panel button functions to different device types.
Mapping rear panel button functions to different device types.
Diagnosing and resolving remote, power, sound, and display problems.
Troubleshooting video, copying, and subwoofer sound issues.
Technical specifications for all unit and remote control sections.
Lists preset codes for controlling various DVD, VDP, VCR, TV, Cable, Satellite devices.
Lists codes for CD, CDR, MD, Tape, and specific DVD models.
Further preset codes for controlling various DVD players.
General| Type | Stereo Receiver |
|---|---|
| Total harmonic distortion | 0.08% |
| Speaker load impedance | 4 - 16 ohms |
| Number of Channels | 2 |
| Outputs | Speaker, Subwoofer |
| Preset Stations | 40 |
| Digital Inputs | Optical, Coaxial |
| Analog Inputs | 6 |
| Tuning range | FM, AM |
| Frequency response | 10 Hz - 100 kHz (+1/-3 dB) |
| Input sensitivity | 200mV |
| Signal to noise ratio | 98dB |
| Video Connections | Composite |
| Power output | 100 W/ch (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
To Next Page
