Why does my Denon DRA-CX3 have power but no sound?
If the power indicator lights up on your Denon Stereo Receiver but no sound is produced, consider the following: * Check that the speaker cables are properly and securely connected. * Ensure you've selected the correct function (input). * Adjust the volume to a suitable level.
How to fix no sound from one side on Denon Stereo Receiver?
If you're not getting sound from one side of your Denon Stereo Receiver, here's what to check: * Make sure the speaker cables are securely connected. * Verify that the input cables are properly connected. * Adjust the left/right balance to ensure it's properly set.
Why is my Denon DRA-CX3 power on but no sound?
If your Denon Stereo Receiver's power indicator is on but you're not getting any sound, here are a few things to check: * Make sure the speaker cables are securely connected. * Ensure you've selected the correct function (input). * Verify that the volume isn't set too low; adjust it to an audible level.
Why does my Denon Stereo Receiver only have sound on one side?
If you're only getting sound from one side of your Denon Stereo Receiver, check these potential causes: * Ensure the speaker cables are properly and securely connected. * Verify the input cables are also securely connected. * Adjust the left/right balance to center the sound.
What to do if the Denon DRA-CX3 remote control does not operate?
If your Denon Stereo Receiver remote control isn't working, try these steps: * Replace the batteries with new ones. * Move closer to the main unit when operating the remote. * Ensure there are no obstructions between the remote and the main unit. * Operate the remote directly in front of the main unit, not at an angle greater than 30°. * Make sure the batteries are inserted correctly.
Why is there a buzzing noise in FM broadcasts on my Denon DRA-CX3?
If you're getting a buzzing noise in FM broadcasts on your Denon Stereo Receiver, it could be due to a few reasons: * The antenna cable might not be properly connected, so ensure it's securely attached. * There may be interference from nearby electronic devices, or the radio signal could be weak. Try repositioning the equipment, connection cables, or antenna. * Consider connecting an outdoor antenna to improve signal reception.
What to do if my Denon Stereo Receiver power indicator does not light up?
If your Denon Stereo Receiver's power indicator doesn't light up and no sound is produced when you turn it on, it's likely that the power cord plug isn't fully plugged in. Check the power cord to ensure it's securely connected.
Why is there hissing or buzzing noise in AM broadcasts on my Denon DRA-CX3 Stereo Receiver?
If you hear hissing or buzzing noises in AM broadcasts on your Denon Stereo Receiver, it could be due to: * Noise interference from a nearby monitor or other electronic devices, or interference in the broadcast signal. To resolve this: * Turn off the monitor. * Change the position or direction of the AM loop antenna. * Connect an outdoor antenna.
Why are the stereo positions inverted on my Denon DRA-CX3 Stereo Receiver?
If you're experiencing inverted instrument positions for stereo sources on your Denon Stereo Receiver, it's likely that the speaker cables or input cables are connected incorrectly. Double-check and correct these connections.
Why is there a humming noise in AM broadcasts with my Denon DRA-CX3 Stereo Receiver?
If you hear a humming noise in AM broadcasts on your Denon Stereo Receiver, it could be due to interference from current in power cords. Try connecting an outdoor antenna to resolve this issue.
General| Impedance | 8 Ω |
|---|---|
| Frequency range | 5 - 40000 Hz |
| Input sensitivity | 150 mV |
| Audio output channels | 2.0 channels |
| Signal-to-Noise Ratio (SNR) | 84 dB |
| Total Harmonic Distortion (THD) | 0.7 % |
| Power output per channel (1KHz@8 Ohm) | 150 W |
| Power output per channel (20-20KHz@8 Ohm) | 75 W |
| Line-in | Yes |
| Audio (L/R) in | 5 |
| Headphone connectivity | 6.3 mm |
| S-Video outputs quantity | 1 |
| Connectivity technology | Wired |
| Speakers connectivity type | Binding post |
| Ethernet LAN | No |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Preset stations quantity | 40 |
| Display | VFD |
| Product color | Silver |
| Audio decoders | Not supported |
| Volume control | Rotary |
| Apple docking compatibility | iPhone, iPod |
| Number of products included | 1 pc(s) |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 105 W |
| Remote control type | RC-1060 |
Weight and Dimensions| Depth | 341 mm |
|---|---|
| Width | 300 mm |
| Height | 80 mm |
| Weight | 5500 g |
To Next Page
