Denon DRA-CX3 - Recording; Tuning in Radio Broadcasts; Presetting; Giving a Name to the Currently Tuned in Broadcast Station and Presetting

ENGLISH
0
Getting Started Connections Troubleshooting Specifications
1
Press FUNCTION to select the input function.
CD
TUNER LINE2LINE3
PHONO LINE1 (iPod)
>
b The function can be switched directly to “TUNER” by pressing
<PRESET>, to “CD” by pressing <CD>.
z
The “iPod” indicator is displayed when a Control Dock for iPod is
connected. (“NO iPod” is displayed if no iPod is connected to the
Control Dock for iPod.)
2
Set the recorder to the recording mode.
b For instructions on operating, see the operating instructions of
the connected component.
3
Start playback on the player.
b For instructions on operating, see the operating instructions of
the connected component.
Recording
• The LINE3 input signal is not output to the recording output terminal
(REC).
• Adjusting the volume or tone does not affect the sound being
recorded.
n
FM station reception conditions
• When the reception band mode is set to “FM AUTO”, the “ST”
indicator lights when a stereo broadcast is tuned in.
• If the signal is weak and the stereo broadcast reception is not
stable, set the reception mode to “FM MONO”. The “MONO”
indicator lights.
n
Auto tuning
Press and hold in <PRESET> or [TUNING] to search for and tune in
the next stereo broadcast automatically.
Stations cannot be tuned in if the signal is too weak.
n
Canceling auto tuning
Press <PRESET> or [TUNING].
n
Manual tuning
The frequency changes one step at a time each time [TUNING] is
pressed.
1
Press [TUNER] , <PRESET> or <FUNCTION> to select
“TUNER”.
The reception frequency is displayed.
2
Press [BAND] to select the reception band.
FM AUTO
FM MONO
AM
3
Press [TUNING] to select the reception frequency.
The “TUNED” indicator lights when a station is tuned in.
Tuning in radio broadcasts
Noise may be produced in the sound when receiving AM broadcasts if
there is e.g. a TV nearby. If so, move the DRA-CX3 and TV as far apart
as possible.
NOTE
If a station is preset at a number where a station has already been
preset, the old setting is deleted and replaced with the new setting.
• A total of 40 FM and AM broadcast stations combined can be
preset.
• Preset stations can be given names of up to 8 characters.
1
Tune in the broadcast station.
The reception frequency is displayed.
2
Press [EDIT].
The name input mode is set.
3
Press [CHANNEL] to select the desired character.
b Up to 8 characters can be input for each preset.
The characters that can be input are as shown below.
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
0         
^ ’ ( ) * + , – . / = (space)
b Press [TUNING] to move the cursor.
b Press [CLEAR] to delete characters.
4
Press [ENTER].
The name input mode is set.
5
Press [CHANNEL] to select the preset number, then
press [ENTER].
The reception frequency and reception mode are preset.
n
To change the name of a preset station:
q Call out the preset name to be changed, then press [EDIT].
w Perform steps 3, 4 under “Giving a name to the currently tuned
in broadcast station and presetting it”.
n
To only preset the station:
q Press [ENTER] while the station is tuned in.
w Perform step 5 under “Giving a name to the currently tuned in
broadcast station and presetting it”.
Presetting
Giving a name to the currently tuned in
broadcast station and presetting it
Operation
1.DRA-CX3E3_ENG.indd 13 2008/02/22 10:20:18