D
davisjosephSep 2, 2025
Why won't my Denon DVD Player start playback when I select a title?
- AAshlee RobinsonSep 2, 2025
If playback doesn't start when you select a title on your Denon DVD player, check the “RATINGS” setting.
To Next PageTo Next PageWhy won't my Denon DVD Player start playback when I select a title?
If playback doesn't start when you select a title on your Denon DVD player, check the “RATINGS” setting.
How to adjust the aspect ratio on my Denon DVD Player?
To correct the picture display in 4:3 or 16:9 on your Denon DVD player, set the “TV ASPECT” default setting to match your connected TV.
What to do if I forgot the rating level password on my Denon DVD-3910 DVD Player?
If you've forgotten the rating level password on your Denon DVD player, while the player is in stop mode, hold the player’s SKIP 9 button and the PLAY button down simultaneously, then hold the OPEN/CLOSE button down for longer than 3 seconds (until “INITIALIZE” disappears from the TV monitor). This will release the lock and return all settings to their default values.
Why are subtitles not showing on my Denon DVD Player?
If subtitles are not displayed on your Denon DVD Player, it could be because: * The DVD does not contain subtitles. * The subtitle setting is turned off. You may need to turn the subtitles setting on.
How to troubleshoot a Denon DVD-3910 that does not turn on?
If your Denon DVD player isn't turning on, make sure the power supply cord is securely plugged into the power outlet.
How to fix no image with HDMI/DVI connection on Denon DVD-3910?
If you're not getting an image with an HDMI/DVI connection on your Denon DVD player, try the following: * Check the HDMI/DVI connection and the status of the HDMI/DVI-related indicators. * Verify that the connected monitor or equipment supports HDCP. The DVD player won't output a video signal without HDCP support. * Check the settings of “HDMI/DVI SELECT.” * Ensure the output format of the DVD player (HDMI/DVI FORMAT) matches the supported input format of the connected equipment. * Confirm that the video output setting at “PURE DIRECT” is not set to “VIDEO OUT:OFF” or “ALL OFF.”
What to do if playback doesn't start or stops immediately on my Denon DVD-3910 DVD Player?
If your Denon DVD player isn't starting playback or stops immediately, here are some things to check: * See if there's condensation on the disc or the player itself. If so, let it stand for 1 to 2 hours. * Make sure you're using a compatible disc. The player supports DVDs, SuperAudio CDs, video CDs, and music CDs. * Wipe off any dirt from the disc.
Why is my Denon DVD-3910 remote not working?
If your Denon DVD player remote isn't working, try these steps: * Make sure the batteries are inserted correctly, matching the “” directions. * Replace the batteries with new ones. * Point the remote at the remote control sensor on the DVD player. * Ensure you're within 7 meters of the sensor. * Remove any obstacles between the remote and the sensor.
What to do if the picture does not appear on my Denon DVD-3910?
If you're not getting a picture on your Denon DVD player, here are a few things to check: * Make sure all the connections are secure. * Ensure that VIDEO OUT has not been set to “VIDEO OUT : OFF” or “ALL OFF” for PURE DIRECT MODE. * Set the TV’s input to “video.” * If you are using HDMI or DVI-D connector, progressive signals from the component video connector will not work. To use the component video output, set HDMI/DVI SELECT to “OFF”.
Why audio or subtitle language does not switch on Denon DVD-3910 DVD Player?
General| Audio DAC | 192kHz/24-bit |
|---|---|
| Progressive Scan | Yes |
| THX Certified | Yes |
| Disc Formats | DVD-Video, DVD-Audio, SACD, CD |
| Video Outputs | Composite, S-Video, Component, HDMI |
| Audio Outputs | Optical Digital, Coaxial Digital |
| Output Resolution | 480p, 720p, 1080i |
| Weight | 17.6 lbs |
