DeVilbiss IntelliPAP Standard User Manual

IMPORTANT! Do not provide these setup instructions to the patient. Only qualified
medical professionals should access these device settings.
Follow these instructions to access the device settings and prepare the device for
patient use. All settings have pre-set values as shown below.
Other Settings
• Filter Cleaning Reminder – Displays a reminder to the patient to clean the filter every 50 hours of use, or approximately every 10 days. This
feature is controlled by the notifications setting and is preset to enabled.
Other setup information
• This device features automatic altitude adjustment for altitudes up to 2743m (9000ft) and needs no manual adjustment.
• This device features a pressure sensor therefore no ne pressure adjustments are needed.
• The SmartLink Data Management System may be used for additional reminders and notications.
• Clear compliance meter by pressing Down key for eight seconds with compliance meter shown (value will go to zero).
All device settings are immediately updated in the device as you make adjustments. When nished press the ON/OFF button once to exit the
Clinical Setup Menu.
Use the LEFT button
and RIGHT button to
navigate through the
menu.
Use the UP button and
DOWN button to adjust
the settings.
First - With the device powered
and turned off, press and hold
the DOWN and DELAY buttons.
Menu Item Description
Factory
Default
Clinical Menu
Language
Selection
Select device language. English
Set
Pressure
Set to CPAP pressure prescribed by doctor.
Range: 3-20 cmH
2
O
10.0 cmH
2
0
Delay
Time
Select period of time to stay at delay pressure. This delay is patient activated.
Range: 0-45 minutes, increments of 5
20 min
Delay
Pressure
If prescribed, set to a level that is comfortable for the patient to fall asleep. This level of pressure is maintained
for the first portion of the delay time and rises to the set pressure in the last 10 minutes of the delay time.
Range: 3 cmH
2
O to CPAP, increments of 0.5
4.0 cmH
2
0
Pressure
Unit
The device operating pressure may be displayed in one of three pressure units: cmH
2
O, hPa or mbar. cmH
2
0
Compliance
Meter
Cumulative hours of “while breathing” time.
N/A
Enable
Menu
Press the  button to enter. Reference the Enable Submenu section for details.
N/A
Lockout
Menu
Press the  button to enter. Reference the Lockout Submenu section for details.
N/A
Enable Submenu
Auto-ON
This option controls the Auto-ON feature, which automatically starts the ow of air after breathing once or
twice into the mask
Enabled
Auto-OFF
This option controls the Auto-OFF feature, which automatically stops the ow of air after taking off the mask.
Disabled
Notifications
Setting to enable mask/filter check notification.
Enabled
Exit
Submenu
Press the  button to exit and return to Clinical Menu.
N/A
Lockout Submenu
Delay Time
Lockout
Used to allow patient access to CPAP delay time setting.
Range: Locked, Unlocked
Unlocked
Exit
Submenu
Press the  button to exit and return to Clinical Menu.
N/A
Quick Set-Up Guide
IntelliPAP™ Standard • SleepCube™ Standard
EN
DeVilbiss Healthcare • 100 DeVilbiss Drive • Somerset, PA 15501 • USA • 800-338-1988 • 814-443-4881
Sunrise Medical Ltd. • Sunrise Business Park • High Street • Wollaston, West Midlands • DY8 4PS • England • 44-138-444-6688
©2007 DeVilbiss Healthcare 12.07
DV51D-125 Rev. A
Second - While holding the
two buttons, press the ON/OFF
button. The display will show
“Clinical Menu”. You can now
access the Clinical Setup Menu.

DeVilbiss IntelliPAP Standard Specifications

General

Device Type	CPAP
Therapy Modes	CPAP
Weight	3.5 lbs (1.6 kg)
Humidifier	Optional
Auto Adjusting	No
Ramp Feature	Yes
Altitude Adjustment	Automatic
Pressure Range	4-20 cm H2O
Ramp Time	0-45 minutes
Data Storage	Yes
Noise Level	26 dBA
Power Supply	AC 100-240V, 50/60 Hz
Power Consumption	90W max

Summary

Clinical Menu Settings

Language Selection

Select the device language for the user interface.

Set Pressure

Set the CPAP pressure as prescribed by a doctor, with a range of 3-20 cmH2O.

Delay Time Setting

Select the duration for the delay pressure, patient-activated, in 5-minute increments.

Delay Pressure Level

Set a comfortable pressure for falling asleep, maintained for the first part of the delay time.

Pressure Unit Configuration

Choose the unit for displaying pressure: cmH2O, hPa, or mbar.

Compliance Meter

Monitors and displays cumulative hours of 'while breathing' time.

Enable Menu Access

Press the down button to enter the Enable Submenu for further settings.

Lockout Menu Access

Press the down button to enter the Lockout Submenu for access control.

Enable Submenu Options

Auto-ON Feature Control

Manages the Auto-ON feature, which initiates airflow upon breathing into the mask.

Auto-OFF Feature Control

Manages the Auto-OFF feature, which stops airflow after mask removal.

Notification Settings

Configure settings to enable mask/filter check notifications.

Exit Enable Submenu

Press the up arrow button to exit this submenu and return to the Clinical Menu.

Lockout Submenu Options

Delay Time Lockout Setting

Allows patient access to the CPAP delay time setting, with options to Lock or Unlock.

Exit Lockout Submenu

Press the up arrow button to exit this submenu and return to the Clinical Menu.

Other Device Settings and Information

Filter Cleaning Reminder

Provides a reminder to clean the filter every 50 hours of use or about every 10 days.

Automatic Altitude Adjustment

Device automatically adjusts for altitudes up to 2743m (9000ft) without manual input.

Pressure Sensor Functionality

Features a pressure sensor, eliminating the need for fine pressure adjustments.

SmartLink Data Management

System can be utilized for additional reminders and notifications.

Clear Compliance Meter

Press and hold the down key for eight seconds to reset the compliance meter to zero.