46
Clothes Door Reversal (OPL only) 50Lb
Step 1: Remove the loading door from the panel Open door and remove inner hinge
plate cover by removing the two Phillips screws. The clothes door may be removed
from the hinge bracket by unscrewing and removing the top 3/16 allen head pivot
screw located at the door upper hinge point, you will also need to use a ¼
allen wrench in the lower fastener. Next lean the door out of the top of
the hinge bracket and lift the door from the bottom hinge pin
Step 2: Open upper service door, and remove lint door.
Step 3: Then remove the two left side phillips screws with beveled washers and the two right
side phillips with beveled washers screws. Next disconnect door switch wires from back
of loading door switch.
Step 4: Next disconnect door switch wires from back of loading door switch. Remove door
switch by depressing the two tabs on switch and remove out front.
Step 5: Remove switch plug from left side and switch to right.
Step 6: Install switch in left side switch hole by inserting from front until switch clips snap
and lock into front panel.
Step 7: Moving Hinge strap from right side to left side. Remove the four Phillips countersunk
screws and remove hinge strap and release the hinge strap back plate. Leave the
Phillips button head in place because it holds the hinge back plate in place.
Step 8: Remove the left side two upper and the two lower Phillips button head screws and
transfer the screws to the right side hinge back up plate. Leave the upper bottom
screws and the lower top screws in place.
Step 9: Move hinge strap to left side, make sure side with pin is on the bottom, reinsert the
four countersunk Phillips head screws.
Step 10: Set door with hinge plate back onto the lower hinge strap pin rst, next using 1/4”
allen wrench and lower door hinge fastener and fastening with the 3/16” allen screw,
next replace the inner door hinge plate cover with the two Phillips head screws.
Step 11: Reconnect Door switch harness and replace front panel in reverse operation.
Clothes Door Reversal (OPL only) 80Lb
Step 1: Remove the loading door from the panel Open door and remove inner hinge plate
cover by removing the two Phillips screws. The clothes door may be removed from the
hinge bracket by unscrewing and removing the top 3/16 allen head pivot screw
located at the door upper hinge point, you will also need to use a ¼ allen wrench in
the lower fastener. Next lean the door out of the top of the hinge bracket and lift the
door from the bottom hinge pin
Step 2: Open upper service door, and remove lint door.
Step 3: Then remove the two left side phillips screws with beveled washers and the two right
side phillips with beveled washers screws. Next disconnect door switch wires from back
of loading door switch.
Step 4: Remove door switch cover, remove the 2 3/8” nuts holding cover, next remove switch
by depressing the two tabs on switch and remove out front.
Step 5: Remove switch plug from left side and switch to right.
Step 6: Install switch in left side switch hole by inserting from front until switch clips snap
and lock into front panel.
Step 7: Moving Hinge strap from right side to left side(Note: on the 80Lb. the hinge back
plate and the stiener have to be moved to the posit side). Remove the four Phillips
countersunk screws and the two button head Phillips screws remove hinge strap and
release the hinge strap back plate.
Step 8: Remove the left side three upper and the three lower Phillips button head screws
transfer the screws and the stiener to the right side hinge position.
Step 9: move hinge strap and hinge back plate to left side, make sure side with pin is on the
bottom, reinsert the four countersunk Phillips head screws and the two button
head screws.
Step 10: Reinstall the switch box cover by replacing the two 3/8 nuts.
Part # 8533-112-001 7/21
To Next Page
Loading...
Need help?
General
