Why Dexter Laundry T-1450 machine tumbles in one direction?
If your Dexter Laundry Washer is only tumbling in one direction, remove the inspection cover at the rear and record any numbers or letters displayed. Consult the fault code section for more information. Additionally, inspect the yellow enable wires from the main relay PCB and at the VFD.
Why is my Dexter Laundry T-1450 Washer vibrating excessively?
Excessive vibration in your Dexter Laundry Washer can stem from several causes. First, check the strength of the mounting structure and ensure mounting bolts are tightened. A worn drive belt can also cause vibration and noise, so inspect its condition. Also, small loads can contribute to out-of-balance loading, increasing vibration.
What to do if the door of my Dexter Laundry T-1450 Washer does not lock?
If the door of your Dexter Laundry Washer isn't locking, first check the display for any error messages and follow the tests described in the fault code section. Then, verify that the door locking mechanism is receiving 120VAC (for 60 Hz models) or 24VAC (for 50 Hz models) from the main relay PCB; if it's receiving power but not functioning, replace the mechanism. Also, check the door switch for continuity through the door latch.
How to open a Dexter Laundry T-1450 door that will not open?
If the door of your Dexter Laundry Washer won't open, check if the thermoactuator and its mechanism are stuck or binding. Ensure the locking thermoactuator is not receiving 24VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 24VAC during the last minute. If the timing and voltage are correct, replace the thermoactuator. Also, verify that the door rod from the mechanism to the lock assembly is long enough to allow the lock assembly to disengage; adjust the rod or the position of the mechanism if needed. Check that the door lock mechanism is not stuck closed; if it is, replace it.
Why is there no cold water entering the tub in my Dexter Laundry T-1450 Washer during wash?
If no cold water is entering the tub of your Dexter Laundry Washer during the wash cycle, start by checking the water valve coil for continuity at the terminals and replace it if necessary. Inspect the water inlet screens for any blockage and clean them if needed. Ensure that the water supply is turned on and functioning correctly. If the appropriate voltage is not present at the valve, refer to the wiring diagram for your specific washer model. Check for voltage at the P4 Connector on the Relay PCB and for LED indication that the appropriate relay is activated. Check the pressure switch continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and if the hose is clear, replace the pressure switch.
Why Dexter Laundry Washer water level is too high?
If the water level in your Dexter Laundry Washer is too high, check the pressure switch hose for any blockages. Also, check the pressure switch for an opening circuit across its terminals. If the contacts do not open, replace the switch.
Why Dexter Laundry Washer machine does not turn?
To troubleshoot why your Dexter Laundry Washer isn't turning, begin by checking the VFD (Variable Frequency Drive). Remove the inspection panel and note any numbers or letters displayed. If there's no display, turn off the power to the machine at the breaker for two minutes, then turn it back on to reset. If the issue persists and there's still no display, consider replacing the VFD.
What to do if Dexter Laundry Washer machine starts and does not operate?
If your Dexter Laundry Washer starts but doesn't operate, check the yellow enable wires from the relay PCB P13 & motor P14 to the VFD to ensure they are connected. Before removing power from the drive, check the fault code on the VFD. Also, check the orange P-15 wire for a signal from the door switches.
Why does my Dexter Laundry T-1450 only tumble in one direction?
If your Dexter Laundry Washer only tumbles in one direction, review the indicator lights displayed on the VFD. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
Why does water drain slowly from my Dexter Laundry Washer?
If your Dexter Laundry Washer is draining slowly, check the hoses and drain valve for any blockages. Ensure the drain size is adequate. If necessary, inspect the building drains for blockages.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-1450 |
| Category | Washer |
| Language | English |
To Next Page
