DieHard 28.71331 - User Manual

Questions and Answers

D
Dylan MartinezAug 3, 2025
What to do if engine start does not work on DieHard 28.71331?
- S
  Susan CamposAug 3, 2025
  If the Engine Start function on your DieHard Battery Charger isn't working, several factors could be at play. You might be drawing more than 200 amps, which reduces crank time. Ensure you wait a full 3 minutes (180 seconds) between cranking attempts to prevent overheating. Check that the charger vents are unobstructed. If the battery is severely discharged, try using the 40A Boost rate for 10-15 minutes before attempting to start the engine.
R
Robert NashAug 9, 2025
How to fix DieHard 28.71331 that will not turn on?
- B
  Briana PerkinsAug 9, 2025
  If your DieHard Battery Charger won't turn on even when properly connected, the issue could stem from a dead AC outlet, a poor electrical connection, or a defective battery. Check the AC outlet's fuse or circuit breaker. Inspect the power and extension cords for loose connections. Also, have the battery checked to determine if it's the root cause.
E
Erika LeonardAug 15, 2025
What to do if the Boost-Charging LED is flashing on DieHard 28.71331?
- M
  Mrs. Rachel AlvarezAug 15, 2025
  If the Boost-Charging LED on your DieHard Battery Charger is flashing, it means the charger has stopped in Boost or Charge mode, possibly due to a bad battery. Have the battery checked and replaced if necessary. Disconnect the charger from the AC outlet, then remove the clamps. Avoid repeatedly trying to charge the battery; instead, have it professionally checked and replaced if needed.
D
David WilliamsAug 21, 2025
Why the Boost-Charging LED does not turn off on DieHard 28.71331 Battery Charger?
- D
  Daniel WrightAug 21, 2025
  The Boost-Charging LED on your DieHard Battery Charger will remain on while the charger is in Boost or Charge mode. This is normal operation. The LED will only turn off once the battery is disconnected from the charger.
R
Roy WallaceAug 27, 2025
What to do if DieHard 28.71331 Battery Charger does not detect a low voltage battery?
- R
  rwallsAug 27, 2025
  If your DieHard Battery Charger isn't detecting a low voltage battery, it might be because the charger was on for more than 5 minutes before being connected to the battery. The clamps are only active for the first 5 minutes. Turn the charger OFF, connect it to the battery, then switch it to the Boost/Charge/Maintain position. Finally, press the rate selection button to activate the charger.

Summary

DieHard Limited Warranty

Important Safety Instructions

Personal Safety Precautions

Preparing to Charge

Charger Location

DC Connection Precautions

Follow These Steps When Battery Is Installed in Vehicle

Follow These Steps When Battery Is Outside Vehicle

Grounding and AC Power Cord Connections

Assembly Instructions

Control Panel

On;Off Switch

Explains the function of the main ON/OFF power switch.

Rate Selection Button

Describes how to select charging rates and modes.

Operating Instructions

Charging a Battery in the Vehicle

Step-by-step guide for charging a vehicle battery.

Charging a Battery Outside of the Vehicle

Step-by-step guide for charging a battery outside the vehicle.

Using the Engine Start Feature

Instructions for using the engine start/jump-start function.

Maintenance and Care

Troubleshooting

Before Returning for Repairs

DieHard 28.71331 Specifications

General

Brand	DieHard
Model	28.71331
Type	Battery Charger
Input Voltage	120V AC
Output Voltage	12V
Battery Type	Lead-Acid
Features	Reverse polarity protection
Compatibility	12V Batteries