To Next PageTo Next PageWhy does my Dimplex Indoor Fireplace circuit breaker trip?
Your Dimplex Indoor Fireplace circuit breaker might be tripping due to a short in the unit wiring. You should trace the wiring in the unit to resolve this. Another possible cause is an improper circuit current rating. Verify that the unit is installed on a dedicated 15 amp circuit.
What to do if my Dimplex Indoor Fireplace heater is not turning off?
If your Dimplex Indoor Fireplace heater is not turning off, it might be due to improper operation of the unit. It can also be caused by improper operation of the Thermostat/Wall Controls (if applicable). Another cause may be a defective heater on/off switch, so consider replacing it. Finally, the heater assembly could be defective and needs replacement.
Why is my Dimplex Indoor Fireplace heater turning off after a couple of minutes?
The Dimplex Indoor Fireplace heater might be turning off after a couple of minutes due to a build-up of dirt/dust in the heater assembly. Ensure that exterior intake louvers and the firebox cavity are free of dirt and dust. Alternatively, the heater assembly could be defective. Replace the heater motor if it's not running when heat is activated, or replace the heater elements if the motor is running but heat isn't coming out.
Why is my Dimplex Indoor Fireplace heater not turning on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, it could be due to several reasons. It might be due to improper operation. Check for loose wiring in the unit. A defective heater switch or a defective remote control receiver (if applicable) could also be the cause. In such cases, replace the heater switch or the remote control receiver kit.
What to do if my Dimplex Indoor Fireplace is making excessive noise with the heater on?
If your Dimplex Indoor Fireplace is making excessive noise when the heater is on, it could be due to a dirty blower assembly. Make sure that the exterior intake louvers and firebox cavity are free of dirt and dust. Another potential cause is a defective heater motor, which would need to be replaced.
Why does my Dimplex Indoor Fireplace unit turn on and off by itself?
Your Dimplex Indoor Fireplace might be turning on and off by itself because the remote control has a similar frequency to other remotes in the area; try replacing the remote control. Radio frequency disturbance from outside sources could also be the reason; in this case, replace the remote control and the Remote Control Receiver Kit, where necessary. A defective Remote Control Receiver could also be the culprit; replace the Remote Control Receiver.
Why is my Dimplex Indoor Fireplace flame not bright?
If the flame in your Dimplex Indoor Fireplace is not bright or not visible, it could be due to burnt light bulbs, so replace them. Loose wiring could also be the cause; check the wiring connections. A defective light harness might also be the problem, so replace the light harness if necessary.
Why does my Dimplex Indoor Fireplace heater emit an odor?
A Dimplex Indoor Fireplace heater may emit an odor due to normal operation, particularly when initially turned on. This occurs as the heater burns off dust accumulated during manufacturing or operation. However, a defective heater assembly can also cause this issue, requiring a replacement.
How to fix Dimplex Indoor Fireplace flame frozen?
To fix a frozen flame in your Dimplex Indoor Fireplace, first check for a defective flicker motor and replace it if necessary. Also, inspect the wiring connections for any looseness and correct them.
What to do if Dimplex Indoor Fireplace does not turn on manually?
If your Dimplex Indoor Fireplace does not turn on manually, it might be due to improper operation. There might be no incoming voltage from the electrical wall socket/Breaker Panel, so check the Fuse/Breaker Panel. Another reason may be loose wiring, so check wiring connections. It could also be a defective On/Off Switch, a defective Heater Switch, or a defective Remote Control Receiver (if applicable), so replace them if needed.
General| Type | Electric Fireplace |
|---|---|
| Fuel Type | Electric |
| Model Number | 6900640559 |
| Brand | Dimplex |
| Voltage | 120 V |
| Flame Effect | Yes |
| Remote Control | Yes |
| Thermostat | Yes |
| Overheat Protection | Yes |
| Power Cord Length | 6 ft |
Covers manual operation for units with/without remote control, including switch functions and indicator lights.
Procedure to synchronize remote control and receiver after power loss, such as breaker trips or power failure.
Explains how to use the remote control to sequentially adjust fireplace flame and heat levels.
Details installation and function of optional wall-mounted controls and thermostats for fireplace operation.
Step-by-step guide for safely removing and replacing burnt-out light bulbs in the fireplace.
Instructions for cleaning the fireplace's glass door, including methods to remove fingerprints and prevent water spots.
Wiring schematic for Mod 0-B, detailing configurations with and without remote controls.
Wiring schematic for Mod C-E, illustrating connections for switches, motor, and elements.
Detailed steps for replacing main on/off and heater control switches on the unit.
Guide for safely removing and installing the flicker motor and flicker rod assembly.
Instructions for safely removing and installing the fireplace's heating elements.
Procedure for safely removing and installing the blower motor and assembly.
Steps to locate, remove, and replace the temperature limit switch.
Guide for safely removing and installing the remote control receiver circuit board.
Steps to convert unit from 208/240V to 120V, specifically for models with remote controls.
Steps to convert unit from 208/240V to 120V, for models without remote controls.
