What does three blinks mean on my Dimplex 6909660400 Indoor Fireplace?
If your Dimplex Indoor Fireplace unit continuously blinks three times, the level sensor assembly may be defective and needs to be replaced.
Why won't my Dimplex Indoor Fireplace turn on with the remote?
If your Dimplex Indoor Fireplace does not turn on with the remote control, first, consult the Operation Section to ensure proper operation. Then, try installing new batteries in the remote control. Make sure the tethered controller is correctly installed, ensuring the connection has clicked into place and a red light is visible. Synchronize the remote to the unit; the unit will flash on and off during synchronization, and completion will be indicated with 5 beeps. Ensure the tethered controller is in an open area to receive the remote signal. If the blue light on the remote doesn't turn on when buttons are pressed, the remote control may be defective and needs replacement.
How to reduce smoke in Dimplex 6909660400 flame effect?
If the flame effect in your Dimplex Indoor Fireplace has too much smoke or is coming out too fast, it could be due to the flame effect control being set too high. Adjust the flame height on both the secondary and/or primary controls to reduce the smoke or speed. Also, check if the filter is missing from the fan housing and insert the fan filter if it is missing.
Why is the flame effect too low on my Dimplex 6909660400?
If the flame effect is too low in your Dimplex Indoor Fireplace, first, adjust the flame height on both the secondary and/or primary controls, as the flame effect control may be set too low. If that doesn't work, check for insufficient air intake and enlarge the area for air to enter the unit, ensuring it reaches the bottom. A defective transducer could also be the cause, so consider replacing it.
How to fix uneven mist on a Dimplex Indoor Fireplace?
If mist is not coming out evenly from your Dimplex Indoor Fireplace, you can take the following steps: * Remove any condensation buildup on the mist outlet. * Adjust the feet under the unit to ensure it is level, front to back and side to side. * Rearrange the media to ensure it is not blocking airflow. * If the transducer is running in test mode, ensure that the emitter is clean and free of calcium deposits or scaling. If it is not running, replace the transducer with the provided additional transducer. * If you are using demineralized water, add 1/8 tsp of table salt to the water reservoir to introduce electrolytes, repeating only when mist is not being produced correctly. * Allow water to warm to room temperature.
Why is my Dimplex 6909660400 making noise on standby?
Some buzzing is normal for Dimplex Indoor Fireplace when the unit is on standby. However, if there is excessive noise, replace the power supply.
How to fix a Dimplex 6909660400 Indoor Fireplace sump not filling?
If your Dimplex Indoor Fireplace sump is not filling from the refill bottle, ensure the unit is level. Place something under the bottle to slope it slightly toward the fill cap so that the water can easily flow to the water reservoir.
Why is my Dimplex 6909660400 Indoor Fireplace not refilling and not showing error blinks?
If your Dimplex Indoor Fireplace unit is not refilling and is not giving error blinks when the water is too high or too low, the level sensor assembly may be defective and needs to be replaced.
What does two blinks mean on my Dimplex 6909660400?
If your Dimplex Indoor Fireplace unit continuously blinks twice, refill the water reservoir so that the level is above the minimum level.
Why won't the flame effect start on my Dimplex 6909660400?
If the Dimplex Indoor Fireplace flame effect will not start and there are no error blinks, note that mist will begin emitting after 45 seconds of operation. If flame is being produced but is not rising beyond the top cover, lift the top cover carefully while the unit is operating. If mist is produced but not rising, refer to section 3.5. Also, put the unit in test mode to test the transducer; if the transducer is running, ensure the emitter is clean and free of calcium deposits or scaling. If the transducer is not running, replace it with the provided additional transducer.
Instructions for connecting the water supply to the Opti-myst® cassette unit.
Overview of the unit's control options and functions for manual, tethered, and remote use.
Procedure to initialize the remote control with the unit for communication.
Details of the two-year limited warranty coverage for products and surrounds.
General| Brand | Dimplex |
|---|---|
| Model | 6909660400 |
| Category | Indoor Fireplace |
| Language | English |
To Next Page
