To Next PageTo Next PageWhy is the ember bed dim on my Dimplex DLG1058?
If the ember bed on your Dimplex Electric Heater is dim and not glowing, check the wiring connections for any loose connections. It could also be due to a defective Ember Bed, which would need to be replaced. Another possibility is a defective Remote Control Receiver, which should be replaced.
Why is my Dimplex Electric Heater making excessive noise?
Excessive noise from your Dimplex Electric Heater could be due to a dirty heater assembly. Ensure that the exterior intake louvers and log grate cavity are free of dirt and dust. Alternatively, the noise may indicate a defective heater assembly, which would then require replacement.
Why is my Dimplex DLG1058 Electric Heater not turning on?
If your Dimplex Electric Heater isn't turning on, it could be due to loose wiring, so check the wiring connections. Another possible cause is a defective heater assembly, which would need to be replaced.
Why is my Dimplex DLG1058 not turning off?
If your Dimplex Electric Heater is not turning off, it may be due to a defective Remote Control Receiver. Replace Remote Control Receiver and Initialize to Remote Control.
Why is my Dimplex DLG1058 making a grinding noise when off?
If your Dimplex Electric Heater is making a grinding noise when it is off, the flicker rod might be hitting or rubbing against internal components. Ensure the rod is straight and mounted properly in the bracket, spinning freely away from other components. Replace if necessary. Alternatively, the flicker motor could be defective and require replacement.
Why is one log dim on my Dimplex DLG1058?
If one log on your Dimplex Electric Heater is dim and not glowing, check the wiring connections for any loose connection. Connect log to another log grate connection to verify if log works. If log works, wiring defective - Replace Log Grate Assembly. If log does not work, LED defective- replace Log.
Why is my Dimplex DLG1058 Electric Heater log grate not turning on in remote mode?
If the log grate on your Dimplex Electric Heater isn't turning on in remote mode, first initialize the remote control. Check wiring connections for any loose wiring. Also, install a new battery into the Remote Control and reinitialize remote control where necessary. Another possibility is a defective Remote Control Receiver, which should be replaced and initialized to Remote Control.
Why are all the logs dim on my Dimplex DLG1058?
If all the logs on your Dimplex Electric Heater are dim and not glowing, check the wiring connections for any loose connections. It could also be due to defective Log Grate wiring, in which case you should replace the Log Grate Assembly.
Why is my Dimplex DLG1058 Electric Heater turning on and off by itself?
Your Dimplex Electric Heater might be turning on and off by itself because the remote control has a similar frequency to other remotes nearby. Try replacing the remote control and initialize to Remote Control Receiver. It could also be due to radio frequency disturbance from outside sources. Try to change the CODE on the Remote Control and initialize Remote Control and Receiver. Another possibility is a defective Remote Control Receiver, which would need to be replaced and initialized to the Remote Control.
Why are the lights dimming when I turn on my Dimplex Electric Heater?
If the lights dim when you turn on your Dimplex Electric Heater, the unit is likely drawing close to the circuit's current rating. Try moving the unit to another outlet or installing it on a dedicated 15 amp circuit.
General| Brand | Dimplex |
|---|---|
| Model | DLG1058 |
| Category | Electric Heater |
| Language | English |
Controls for On/Off, 2-Position, and Initialization switches.
How to reset the heater after automatic shut-off due to overheating.
Instructions for installing batteries and general remote control information.
Steps for remote initialization, reprogramming, and resolving frequency interference.
Detailed guide to all buttons and features of the remote control unit.
Instructions for using the child lock to prevent accidental operation.
Guidelines for cleaning the log grate surfaces using a damp cloth.
Recommends using authorized service representatives for any maintenance.
Outlines the coverage, duration, and applicability of the one-year limited warranty.
Specifies what the warranty doesn't cover and how to seek service.
Details limitations of liability and state/provincial law application to the warranty.
