How to fix Dimplex Indoor Fireplace when flame is not bright?
If the flame in your Dimplex Indoor Fireplace isn't bright or visible, the light bulbs might be burnt out, so replace them. Also, check for loose wiring connections. A defective light harness could also be the cause, requiring replacement.
Why is my Dimplex Indoor Fireplace making excessive noise when the heater is on?
If your Dimplex Indoor Fireplace makes excessive noise when the heater is on, it could be due to a dirty Heater Assembly. Ensure the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the Heater Assembly may be defective and require replacement.
Dimplex EF3003 Indoor Fireplace: heater fan on, but no heat?
If the heater fan on your Dimplex Indoor Fireplace turns on but doesn't produce heat, first, refer to the Operation Section for proper operation. Check for loose wiring in the unit. It could also be a defective Heater Assembly, which would need to be replaced.
Why do lights dim when Dimplex EF3003 Indoor Fireplace is on?
If the lights dim in the room when your Dimplex Indoor Fireplace is on, the unit might be drawing close to the circuit's current rating. Try moving the unit to another outlet or installing it on a dedicated 15 amp circuit.
Why does my Dimplex Indoor Fireplace heater emit an odor?
If your Dimplex Indoor Fireplace heater emits an odor, it may be normal if it's a brief period after the heater is initially turned on, as it burns off dust accumulated during manufacturing or operation. However, a defective Heater Assembly could also be the cause, requiring replacement.
What to do if Dimplex Indoor Fireplace does not turn on manually?
If your Dimplex Indoor Fireplace isn't turning on manually, first, refer to the Operation Section for proper operation. Check the Fuse/Breaker Panel to ensure there's incoming power from the electrical wall socket. Also, inspect wiring connections for any looseness. A defective switch (3-Position or On/Off) or a defective Remote Control Receiver could also be the problem, requiring replacement.
Why does my Dimplex Indoor Fireplace heater turn off after a few minutes?
If the heater on your Dimplex Indoor Fireplace turns off after a few minutes, it could be due to a buildup of dirt or dust in the heater assembly. Ensure the exterior intake louvers and firebox cavity are free of dirt and dust. Alternatively, the Heater Assembly may be defective and require replacement.
How to fix Dimplex EF3003 heater if it's not turning on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, but the flame effect works, first, refer to the Operation Section for proper operation. Second, check for loose wiring in the unit. It could also be a defective Heater On/Off switch, which would need replacement. Lastly, a defective Heater assembly could be the cause, requiring replacement.
Why does my Dimplex Indoor Fireplace turn on and off by itself?
If your Dimplex Indoor Fireplace turns on or off by itself, the remote control might have a similar frequency to others nearby. Try changing the frequency of the Remote Control, referring to the Operation Section. Radio frequency disturbance from outside sources could also be the cause, so again, change the remote control frequency. If issues continue, replace the Remote Control and Receiver, and initialize them. A defective Remote Control Receiver could also be the culprit, so replace it and initialize it with the Remote Control.
What to do if Dimplex EF3003 Indoor Fireplace does not turn on using the remote control?
If your Dimplex Indoor Fireplace isn't turning on with the remote control, ensure the remote is initialized to the fireplace. If not, initialize the remote control. Also, the remote control might not be working correctly, so install a new battery and reinitialize if needed. If problems persist, consider replacing the Remote Control or Remote Control Receiver and then initialize them.
General| Type | Electric Fireplace |
|---|---|
| Weight | 40 lbs |
| Remote Control | Yes |
| Fuel Type | Electric |
| Voltage | 120 V |
| Flame Effect | LED Flame Effect |
| Wattage | 1, 500 Watts |
| BTU | 5100 BTU |
| Heating Area | 400 sq ft |
Steps to set up and pair the remote transmitter with the fireplace.
Operating the fireplace features using the remote control.
Using the physical power switch located on the fireplace unit.
Procedure to reset the heater's safety overheat protection.
To Next Page
