To Next PageTo Next PageWhat to do if Dimplex Indoor Fireplace LEDs blink once every 8 seconds?
If the LEDs on your Dimplex Indoor Fireplace continuously blink once every 8 seconds on one side, it indicates overflow detection on that side. Switch off the product and the water supply, then contact your dealer for assistance.
Why Dimplex Indoor Fireplace LEDs continuously blink three times?
If the LEDs on your Dimplex Indoor Fireplace continuously blink three times, it indicates that the time from maximum level to minimum level is too short, or there are conflicting water level readings. Ensure there are no leaks in the sump, that the floats are moving freely within the sump, and that the product is level.
What does it mean if Dimplex Indoor Fireplace LEDs continuously blink twice?
If the LEDs on your Dimplex Indoor Fireplace continuously blink twice on one side, it indicates a low water reading on that side. If this happens during the first fill, refer to the ‘Initial Product Start Up’ section. If the product uses a water tank, refill it and reset by switching off ‘Switch A’ for 20 seconds, then switching it back on, or reset using the remote control. Also, check if the Leak Prevention Valve has been activated and replace the pad if needed.
What to do if Dimplex Indoor Fireplace LEDs continuously blink four times?
If your Dimplex Indoor Fireplace's LEDs continuously blink four times, it indicates that the fill time from minimum to maximum level has been exceeded. If this occurs during the initial fill, refer to the ‘Initial Product Start Up’ section. If the product is fed by a water tank, refill it and reset the product by switching off ‘Switch A’ for 20 seconds, then switching it back on, or reset the error using the remote control. If the product is fed from a mains water supply, ensure sufficient water pressure.
What to do if Dimplex Indoor Fireplace remote control stops working?
If your Dimplex Indoor Fireplace remote control stops working, there are several potential causes. First, check the positioning of the Bluetooth Receiver, ensuring it is not encased in metal or concrete, which can affect the Bluetooth range. Next, check the connection to the jack. Finally, replace the batteries with two new AAA batteries.
How to fix Dimplex Indoor Fireplace with little or no mist?
If your Dimplex Indoor Fireplace produces little or no mist, several factors could be responsible. First, check the transducer's operation and clean it and the sump thoroughly. Ensure the transducer sits correctly in the sump. Also, remove and clean the air filter, making sure to place it back correctly. Finally, ensure the nozzle is correctly positioned on the sump and clean the sump, transducer, and nozzle thoroughly to resolve any blockages.
Why does my Dimplex Opti-Myst Cassette 500 flame effect have too much smoke?
If the flame effect on your Dimplex Indoor Fireplace is producing too much smoke, the flame effect setting may be too high. Try turning down the flame effect and allow some time for the flame generator to adjust to the new setting.
What to do if my Dimplex Opti-Myst Cassette 500 Indoor Fireplace smells unpleasant when used?
If your Dimplex Indoor Fireplace emits an unpleasant smell during use, it could be due to: * Dirty or stale water. Clean the unit. * Using unfiltered tap water. Switch to using only filtered tap water.
How to fix Dimplex Indoor Fireplace when the flame effect won't start?
If the flame effect on your Dimplex Indoor Fireplace isn't starting, there are a few things to check: * Ensure the mains plug is correctly plugged into the wall socket. * Verify the water tank is full and there's water in the sump. * Confirm the low voltage connector is properly connected.
What to do if Dimplex Opti-Myst Cassette 500 Indoor Fireplace won't operate and LEDs blink twice?
General| Product Name | Dimplex Opti-Myst Cassette 500 |
|---|---|
| Category | Indoor Fireplace |
| Style | Modern |
| Technology | Opti-Myst |
| Installation | Built-in |
| Remote Control | Yes |
| Fuel Type | Electric |
| Water Tank Capacity | 1.5 liters |
| Runtime per Tank | 8 hours |
| Type | Electric Fireplace |
| Flame Effect | Realistic 3D Flame Effect |
| Weight | 15 kg |
| Power Supply | 230V, 50Hz |
| Log Set/Bed Options | Included |
