What to do if my Dimplex Prism BLF5051 Indoor Fireplace heater fan runs continuously?
If the heater fan in your Dimplex Indoor Fireplace runs continuously, check for loose wiring in the unit. If the wiring is secure, the remote switchboard or blower/fan may be defective and require replacement.
What to do if my Dimplex Prism BLF5051 does not turn on with the manual controls?
If your Dimplex Indoor Fireplace doesn't turn on with the manual controls, refer to Operation Section. Check the fuse/breaker panel and wiring connections. If the issue continues, the switchboard may be defective and require replacement.
Why does my Dimplex Prism BLF5051 heater emit an odor?
A brief odor from your Dimplex Indoor Fireplace heater is normal when initially turned on, as it burns off dust accumulated during manufacturing or operation. However, if the odor persists, the heating element may be defective and require replacement.
Why is my Dimplex Prism BLF5051 power cord getting warm?
The power cord of your Dimplex Indoor Fireplace may get slightly warm during normal operation when the heater is on. However, if the cord gets hot to the touch, replace it, as this indicates a defective power cord.
What to do if my Dimplex Indoor Fireplace heater fan turns on but there is no heat?
If the heater fan in your Dimplex Indoor Fireplace turns on but lacks heat, refer to Operation Section. Also, check for loose wiring in the unit. If these steps don't resolve the issue, the heating element may be defective and require replacement.
What to do if my Dimplex Indoor Fireplace is making excessive noise with the heater on?
If your Dimplex Indoor Fireplace makes excessive noise when the heater is on, ensure that the exterior intake louvers and firebox cavity are free of dirt and dust. If the issue persists, the blower/fan might be defective and require replacement.
What to do if my Dimplex Indoor Fireplace heater is turning off after a few minutes?
If your Dimplex Indoor Fireplace heater turns off after a few minutes, refer to Operation Section. Also, ensure that the exterior intake louvers and firebox cavity are free of dirt and dust. A defective heating element could also be the cause, requiring a replacement.
Why do lights dim in the room when my Dimplex Prism BLF5051 Indoor Fireplace is on?
Lights dimming when your Dimplex Indoor Fireplace is on indicates that the unit is drawing close to the circuit's current rating. To resolve this, move the unit to another outlet or install it on a dedicated 15 amp circuit.
Describes how to turn the unit on and off using the remote or unit controls.
Explains how to activate and cycle through different flame effect settings.
Details controlling heat settings, including low/high heat and a dedicated heat-only mode.
Covers adjusting temperature set points and switching between Celsius and Fahrenheit.
Explains how to change and hold preset ambient lighting color combinations.
Details how to modify the brightness of the unit's internal lights.
Explains setting the timer to automatically shut off the fireplace.
Provides instructions for cleaning the fireplace's reflective glass panel.
Outlines the method for cleaning the exterior painted surfaces of the fireplace.
Advises on when to seek professional service for the unit.
Details the process for removing units mounted directly onto a wall surface.
Explains how to remove fireplaces installed partially within a wall.
Provides instructions for removing fireplaces installed fully recessed within a wall.
General| Model | BLF5051 |
|---|---|
| Type | Electric Fireplace |
| Width | 50 inches |
| Power Source | Electric |
| Color | Black |
| Remote Control | Yes |
| Voltage | 120V |
| Heating Area | Up to 400 sq. ft. |
| Flame Colors | Multi-Color |
| Adjustable Flame Brightness | Yes |
| Adjustable Thermostat | Yes |
| Timer | Yes |
| Material | Metal and Glass |
| Installation | Wall-Mount |
| Flame Effect | Yes |
| Wattage | 1500W |
To Next Page