To Next PageTo Next PageWhy DKS Gate Opener operator will not run and entrapment protection input(s) LED is ON?
If the DKS Gate Opener operator will not run and the entrapment protection input(s) LED is ON, the entrapment protection device has a fault or the wiring to it is shorted.
General| Brand | DKS |
|---|---|
| Model | 6500 Series |
| Category | Gate Opener |
| Language | English |
Details settings for the top 8 DIP switches on the circuit board.
Details settings for the bottom 4 DIP switches on the circuit board.
Details the function and wiring of the 4-pin terminal block.
Details the function and wiring of the 20-pin main terminal block.
Details gate class, type, entrapment devices, and model specifications.
Outlines mandatory entrapment protection for gate safety and UL 325 compliance.
Specifies gate construction standards for automated vehicular gates.
Provides critical instructions for safe and proper gate operator installation.
Lists common hazards associated with gate operator systems.
Categorizes gate operators based on their application and safety requirements.
Defines types of entrapment protection required for gate operators.
Details requirements for conduit installation for gate operator wiring.
Specifies dimensions and placement for the operator's concrete pad.
Layout and arm calculations for gates up to 22 ft with 48" attachment.
Layout and arm calculations for gates up to 22 ft with 46" attachment.
Layout and arm calculations for gates up to 14 ft with 36" attachment.
Layout and arm calculations for gates up to 8 ft with 28" attachment.
Highlights critical setup points for bi-parting gates with overlaps.
Instructions for securely mounting the operator to the concrete pad.
Steps for attaching the gate bracket to the operator's crank arm.
Guidance on properly installing warning signs for gate safety.
Illustrates mounting height and distance for UL photo sensors.
Details wiring for monitored OPEN and CLOSE photo sensors.
Specifies wire sizing and distance limitations for AC power runs.
Explains how to connect incoming high voltage AC power to the operator.
Details the control board connections for the primary operator.
Explains wiring between primary and secondary operators.
Overview of key components and functions on the 4405 circuit board.
Guide to setting DIP switches for various operator functions.
Defines the function of each of the top 8 DIP switches.
Defines the function of each of the bottom 4 DIP switches.
Guides adjustment of the primary operator's opening and closing limit sensors.
Guides adjustment of the secondary operator's opening and closing limit sensors.
Details how to adjust the reverse sensitivity for the primary operator.
Instructions for adjusting reverse sensors on dual gate systems.
Provides sample wire turns for secondary current sensor based on motor HP.
Details the function and wiring for main terminal blocks.
Wiring details for the 4-pin non-removable terminal.
Wiring details for the 20-pin main terminal block.
Wiring instructions for the Fire Dept Open activation device.
Wiring for various access control devices like key switches and keypads.
Details wiring for entrapment protection devices to the UL 325 terminal.
Wiring guidance for monitored photo sensors.
Shows configuration for wireless reversing edge systems.
Shows configuration for hardwired reversing edge systems.
Wiring details for automatic exit loops for free exit.
Wiring instructions for shadow loops to hold gates open.
Wiring for reverse loops to prevent closing on vehicles.
How to use the main power and reset switches for operator control.
Explains scenarios leading to a soft shutdown and how to reset.
Explains scenarios leading to a hard shutdown with alarm.
Procedure for resetting the operator after a hard shutdown.
Guidelines for emergency vehicle access during power failures.
Provides a monthly schedule for gate operator maintenance checks.
Lists common symptoms and possible solutions for operator issues.
Explains the meaning of different audio tones indicating system faults.
Lists available monitored entrapment protection devices for UL 325 compliance.
Lists loop detectors, magnetic locks, heaters, and other optional accessories.
Lists part numbers for gearbox shaft extension replacement components.
Explains hard shutdown conditions and how to reset the operator.
Step-by-step guide for manually operating the gate.
Guide for performing visual inspections of the gate operator.
Procedures for testing reversing sensors, photo sensors, and reversing edges.
