Dormakaba ED50LE Installation Instructions

Name: Dormakaba ED50LE
Brand: Dormakaba
Rating: 4 (1 reviews)

124 pages

To Next Page

ED900

Low Energy Swing Door Operator

(Fine cover)

Double egress doors

Installation Instructions

08125330 – 02-2020

| EN |

Default Chapter2
- Table of Contents2
- ED900 Arm Configurations4
- Product Description 55
- Handing of Door5
- Double Egress Door Installation Configurations6
Safety Information7
ED900 Product Overview8
- ED900 Push Arm System8
- ED900 Pull Arm System8
- ED900 - Double Egress Door Configurations9
- ED900 Operator Component Views10
ED900 Hardware - Double Door12
- ED900 Operator and Mounting Plate12
- Door Decal Kit, Low Energy12
- Double Door Communication Cable12
- Arm Assemblies13
- Axle Extension Sleeves and Extensions13
- ED900 Mounting Plate Screw Kit14
- ED900 Arm Mounting Screw Kits14
- ED900 Standard Cover Kit14
- ED900 Full Width Cover, Mounting Plate Extension, and Cables - Option15
- Key Switch Panels - Option16
- Push Arm Door Stop - Option16
- Conduit Box and Wiring Kit - Options17
Technical Data18
- ED900 Technical Data18
- Operating Specifications19
Operational Mode Overview19
- ED900 Door Closer Modes19
- Low Energy Product19
User Interface20
- Overview20
- Button Keypad and Display20
- Program and Exit Only Switches21
- Operator Status Leds21
System Accessories22
- System Accessory Electrical Connections22
- ED900 Terminal Board Interfaces23
ED900 Door Signage24
- Low Energy Operator24
- Door Signage, Low Energy Double Egress Swing Door25
- Safety Information Label, Low Energy Swing Doors26
11 Recommended Tools and Torque Chart27
- Recommended Tools27
- Standard Tightening Torque27
- Drill Bits27
12 ED900 Installation Overview28
- Installation Preparation28
- 12.2 ED900 Operator Installation with Standard Covers30
- ED900 Operator Installation with Full30
- ED900 Operators - Assign Active Door and 8 Inactive Door Type30
- ED900 Operators - 115 Vac Customer31
- ED900 Operators - Program Switch31
- Interconnecting Cables31
- Wiring31
13 ED900 Installation Templates32
- Installation Templates - Pull Arm32
- Installation Templates - Pull as Push35
- Installation Templates - Push Arm36
- Installation Templates, Double Doors38
14 ED900 Operator and Mounting Plate42
Preparation42
- Remove Mounting Plate from each ED90042
- Operator44
- Options - Customer 115 Vac Connection to Terminal Blocks44
- Full Width Cover Option46
- ED900 Operator Preparation and 19 Mounting Plate Assembly46
15 ED900 Mounting Plate and Operator48
Installation48
- 15.1 ED900 Mounting Plate Attachment to48
- Install ED900 Mounting Plate to Jamb And/Or Wall49
- Full Width Cover Option - Install Cables between Mounting Plates50
- Mounting Plate50
  - Connect Customer 115 Vac to ED900 Mounting Plate Terminal Block52
  - Route Accessory Wiring to Active Door Mounting Plate53
- Remove Protective Film Strips from each ED900 Operator54
- Install each ED900 Operator Onto Its54
- Mounting Plate54
- Full Width Cover Option - Install Program Switch, Active Door ED90055
- Full Width Cover Option - 115 Vac Pair Power Cable Connections56
  - Push Arm Installation Templates57
- Arm with Track Mount Installation60
  - Arm with Track Installation60
  - Splined Arm and Track Assemblies60
  - Splined Arm and Track Hardware60
  - Install Hardware into Track61
  - Slide Shoe Assembly61
  - Fasten Track Assembly to Door62
  - Arm Assembly63
  - Arm Assembly with CPD Lever63
    - Fasten Arm to ED900 Operator64
- Measure Door Width, Reveal Depth66
  - Door Width Parameter Tb66
  - Record Door Width Measurement, Tb Value66
  - Tb Parameter Values66
  - Measure and Record Reveal Depth67
  - Rd Parameter Values67
  - Reveal Depth Parameter Rd67
- Operator Spring Tension68
  - Set ED900 Operator Spring Tension68
- Braking Circuit Plug69
  - Braking Circuit Plug Position69
- Power Fail Closing Speed70
  - Set Power Fail Closing Speed70
    - Parameters71
  - First Commissioning74
- Single Door First Commissioning74
  - Set Configuration Parameters75
  - Set Parameter PS, Program Switch Type76
  - Perform Learning Cycle77
- Double Door First Commissioning78
  - Separately Commission Active and Inactive Doors78
  - Set Operator Parameters for Double Door Operation78
  - Connect Communication Cable between Operators80
- Connect Accessory Wiring and Test81
  - Install Accessory Wiring81
  - Test All Accessories81
- Set Track Bumper Stop82
  - Set Track Bumper Stop Position82
- Install Push Arm Door Stop83
  - Install Push Arm Door Stop (Optional Assembly)83
- 28 Install ED900 Cover, End Caps and 57 Spindle Caps84
  - Install Cover and End Caps84
  - Install Spindle Caps85
  - Full Width Cover Option - Install Cover and End Caps86
- 29 Install Door Signage87
- 30 ANSI/BHMA Standards88
  - A156.19 Low Energy Power Operated Doors88
- 31 Upgrade Cards90
  - Container Module90
  - Installing Upgrade Cards91
- Maintenance92
  - Safety Label, Low Energy Swing Doors92
  - ED900 Environment and Cleaning93
  - Yellow LED, Service Level93
  - Pull Arm Maintenance94
  - Arm Fasteners - Torque Requirements95
  - Push Arm Maintenance96
  - ED900 Brake Maintenance97
Appendix A - Driving Parameters - Detail99
- Driving Parameters Detail99
Appendix B - Troubleshooting108
- Red LED Status Codes109
- Troubleshooting Chart, "Ln" Codes110
- Troubleshooting Chart, "E" Codes111
Appendix C - Dormakaba Handheld113
- Dormakaba Handheld Terminal113
- Dormakaba Handheld; Configuration Parameters114
- Dormakaba Handheld; Driving Parameters115
- Dormakaba Handheld; Special Functions116
  - (Upgrade Cards) ED900116
- Dormakaba Handheld; Diagnostics117
- New Dormakaba Handheld; Language119
- Dormakaba Handheld; Firmware Update120
Appendix D - Wiring Diagrams122
- D1.1 Key Switch Panel with RJ45 Connector122
- D2.1 Key Switch Panel123

Other manuals for Dormakaba ED50LE

Owner's Manual14 pages

Troubleshooting Instructions54 pages

Quick Start Guide2 pages

Questions and Answers:

Need help?

Do you have a question about the Dormakaba ED50LE and is the answer not in the manual?

Dormakaba ED50LE Specifications

General

Opening Speed	Adjustable
Closing Speed	Adjustable
Opening Width	Adjustable
Product Type	Electromechanical Door Operator
Operating Modes	Automatic, Manual
Safety Features	Obstacle detection
Finish	Anodized aluminum
Holding Force Adjustment	Yes

Related product manuals

Dormakaba ED-IG Series

Dormakaba GSR-EMR XEA BG

4 pages

Dormakaba ES 200 EASY PLUS

8 pages

Dormakaba ED50LE Installation Instructions

Table of Contents

Other manuals for Dormakaba ED50LE

Questions and Answers:

Dormakaba ED50LE Specifications

Related product manuals